manualshive.com logo in svg

Honeywell INNCOM e528 Series, Product Manual, Page: 15 / 15

Share
Download
Honeywell INNCOM e528 Series Product Manual Download Page 15

E528 Product Guide 

 

Rev 8.0 12/16/2016

 

15

 

 

 

Document Revision History 

 

REVISION  

DATE ISSUED  

REASON FOR CHANGE  

First issue  

26-Apr-2006  

v1  

30-Jul-2007  

Reformatted for consistency with other product guides. Information about the  

other e4 models added to the Overview section. Information on all ordering  

options and new features added to the Ordering section.  

v2  

Not issued  

Product photos updated. Part number corrected. Figure 3 redrawn.  

v3  

27-Jun-2008  

New Figure 2 added (PIR range figures) and figure numbers changed to 

accommodate the added figure.  

v4  

30-Jun-2008  

Switched to new document format.  

v5  

30-Jun-2008  

Error in Figure 4 corrected; font discrepancies corrected.  

v6  

18-Feb-2010  

Reformatted to new template, RF data updated  

v6.1  

22-Apr-2010  

OP/N rewritten to include old scheme; photos updated.  

v6.2  

28-Oct-2010  

Added 3G pinout note  

v7.0  

05-Apr-2012  

Added 4G information  

v7.1  

18-Dec-2012  

Revised FCC/IC statements  

v7.2  

12-Feb-2013  

Removed ordering information  

V7.3  

10-Feb-2014  

Updated connector photos 

V8 

15-Dec-2016 

Reformat to HON branding. Remove G2 Legacy info 

 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

 

The material in this document is for information purposes only.  The content and the product it describes are subject to change without notice.  

Honeywell makes no representations or warranties with respect to this document. In no event shall Honeywell be liable for technical or editorial 

omissions or mistakes in this document, nor shall it be liable for any damages, direct or incidental, arising out of or related to the use of this document.  

No part of this document may be reproduced in any form or by any means without prior written permission from Honeywell. 

Copyright © 2016 by Honeywell International, Inc.  All Rights Reserved. 

 

Honeywell  I  277 West Main Street  I  Niantic, CT 06357  I  Phone: 1.860-739-4468  I  www.INNCOM.com 

Summary of Contents for INNCOM e528 Series
















Reviews:

No comments