manualshive.com logo in svg

Honeywell HP970A, Service Data, Page: 8 / 10

Share
Download
Honeywell HP970A Service Data Download Page 8

 BAND 

 

 HUMIDISTATS

TYPICAL

PNEUMATIC

/ A S S E M B L Y

Follow steps   through 4 of 

Unhook the coil spring of the element assembly from

the 

 assembly bracket (Fig. IO).

Unhook the bias spring from its anchor post.
Remove the frame post and mounting screw.
Lift the nozzle/flapper assembly from the base.
Remove the O-ring from the rear of the nozzle/flapper

assembly.
Disengage the other end of the bias spring from the
bracket hole. Do not lose the small pin located inside

the spring.
Assemble the O-ring and the bias spring to the

replacement nozzle/flapper assembly and reinstall in
reverse order.
Recalibrate the 

FILTER CARTRIDGE

Reinstall the tiumidistat cover.

 AND

M

O

U

N

T

I

N

G

SCREWS (4)

When replacing these parts, use extreme care to
prevent dirt, dust, or debris from entering various
openings of the Humidistat base or the restrictor
block.

Remove the 

 cover.

Remove the Humidistat.

Fig. Il. Restrictor Block Assembly and Filter

Cartidge Replacement.

Access to the restrictor block assembly and filter

cartridge is from the rear of the base assembly.

Remove the four mounting screws from the restrictor

block (Fig. 
Carefully lift off the restrictor block (Fig. 11).

Remove the flat rubber gasket from the restrictor

block. The filter cartridge is located in the gasket.

Remove the filter cartridge from the gasket.

Align the gasket on the base assembly, and insert the
new filter cartridge into the recess in the base with the

screen end of the filter exposed.

Place the new restrictor block over the hasket and

filter 

 and replace the four mounting screws.

Snap the 

 onto the mounting 

Recalibrate the 

 the 

 cover.

 9.5

Summary of Contents for HP970A











Reviews:

No comments