2 | HD262 TDN IR Indoor Dome Camera
www.honeywellvideo.com
+1.800.796.CCTV (North America only)
© 2012 Honeywell International Inc. All rights reserved. No part of this publication may be reproduced by any
means without written permission from Honeywell. The information in this publication is believed to be accurate
in all respects. However, Honeywell cannot assume responsibility for any consequences resulting from the use
thereof. The information contained herein is subject to change without notice. Revisions or new editions to this
publication may be issued to incorporate such changes.
Document 800-11990 – Rev B – 06/2012
3. Package Includes
•
Camera (1)
•
Quick Install Guide (1)
•
User Guide (1)
•
Screws (2)
•
Video test cable (1)
•
2-conductor pigtail (1)
4. Key Features
•
1/3
″
interline transfer CCD
•
True Day/Night with movable IR cut filter
•
620 TV lines resolution
•
2.8–12 mm (F1.4) VFAI lens, F1.4
•
0 lux minimum illumination (IR LEDs on)
•
Up to 65 ft (20 m) of IR illumination
•
Sens-up (×2 to ×1024)
•
Digital noise reduction (DNR)
•
Backlight compensation (BLC)
•
Motion detection (4 zones)
•
Privacy masking (8 zones)
•
Local video output
•
Dual power (24 VAC/12 VDC)
5. Connecting the Cables
Video (Yellow)
BNC
Power (Red)
24 VAC/12 VDC
Power (+)
Power (–)
Video Signal
Video GND
POWER
VIDEO
6. Setting Up the Camera
1.
Remove the dome cover from the base. Insert a coin into the slot and
twist to pry the cover from the base.
2.
Connect the video and power cables to the camera.
3.
Attach the base to the mounting surface using the supplied screws.
4.
Connect a portable monitor to the 2-pin video out connector on the
camera control board using the supplied video test cable.
5.
Open the lens shroud to expose the focus
and zoom controls. Brace your forefinger
against the back of the lens assembly
and pull back the shroud with your thumb
(see photo).
6.
Position the camera and adjust zoom and
focus as needed.
7.
Configure the camera on-screen display (OSD) menu settings using the
OSD controller on the camera control board.
8.
Close the lens shroud and replace the dome cover, aligning the
on
the cover with the red “LOCK” mark on the base (see drawing below).
OSD Controller
Video Out
Zoom
Focus
Securing Dome Cover
Align “LOCK”
and “
” to
install cover.
7. Specifications
Video Standard
NTSC
Scanning System
2:1 Interlace
Image Sensor
1/3” interline transfer CCD
Number of Pixels (H × V)
768 × 494
Minimum Illumination
0 lux (IR LEDs on)
Horizontal Resolution
620 TVL
Video Output
1.0
V
p-p, 75 ohms
Sync System
Internal/Line lock
S/N Ratio
50 dB or more (AGC off)
Lens Type
2.8–12 mm VFAI, DC drive, F1.4
IR LEDs
850 nm, 28 LEDs
IR Illumination Distance
Up to 65 ft (20 m)
DNR
Auto/Off/Low/Mid/High
BLC/HSBLC
Off/On
Day/Night
Color/BW/Auto/Ext
Gain Control
Off/Low/Mid/High
White Balance
ATW/AWC/Manual
Sens-Up
Auto (×2 to ×1024)
Motion Detection
Off/On (4 programmable zones)
Privacy Masking
Off/On (8 programmable zones)
D-WDR
Off/On (Level adjustable)
Sharpness
Off/On (Level adjustable)
Mirror
Horizontal
Smart IR
Off/On (Level adjustable)
Input Voltage
24 VAC/12 VDC
Power Consumption
5 W (max)
Temperature
Operating: 14°F to 122°F (–10°C to 50°C), RH 95% max
Storage: –4°F to 140°F (–20°C to 60°C), RH 95% max
Dimensions (L × W × D)
5.12” × 5.12” × 4.02” (130 mm × 130 mm × 102 mm)
Weight
0.66 lb (300 g)
