background image

Duress code 

Use a duress code if you are forced to disarm your security 
system under duress. Your duress code is obtained by adding 1 
to the last digit of your code (e.g. 1234 => 1235, 6789 => 6780). 

The system will disarm as normal but a silent alert signal is 
transmitted to your alarm company (depending on the 
configuration). 

Switch on/off receivers 

Note:

 This function is optional, and can be set at installation. 

It is possible to switch on/off receivers (such as smart plugs) from 
the keypad. 

To switch a receiver on/off: 

1.  Press the 

 key

 

to switch the selected receiver on or the

key to switch the selected receiver off. 

2.  Select the desired receiver by pressing a key corresponding to 

the receiver number 0 to 9 (0 corresponds to receiver number 
10). 

A high beep is played if the receiver is driven successfully; 
otherwise a low beep is played. 

 

Remote Maintenance (optional) 

Note:

 This function is optional and depends on the panel 

configuration. 

Press the 

 +

 keys simultaneously to activate the remote 

maintenance function as configured by your installer. Ask your 
installer for more information on this function.  

 

 

Summary of Contents for GKP-S8M



















Reviews: