manualshive.com logo in svg

Honeywell Gent Vigilon Compact, Operating Instructions Manual

Share
Download
Honeywell Gent Vigilon Compact Operating Instructions Manual Download Page 21

Typical fault messages

The following table shows some of the more typical fault messages that may occur along with their meaning
and possible rectification action.

Message

Indication

Meaning

Action

Mains failed

The mains supply to the control
panel has failed.

Restore the mains supply to
the control panel.

Battery
discharged

The battery supply to the control
panel has been fully discharged.

Check the battery and replace
if necessary.

Battery
disconnected

The battery supply to the control
panel has been disconnected.

Reconnect the battery.

ACC loop 1 OC

There is an open circuit wiring
fault on the audio loop circuit.

Check the wiring and rectify the
fault.

ACC loop 1 SC

(1, 4)

There is an open or short circuit
wiring fault on the audio loop
circuit. The numbers (1,4) signify
loop and micro DAU device at
which the wiring fault has been
detected.

Check the wiring and rectify the
fault.

Speaker
circuit OC or
SC

There is a open or short circuit
wiring fault on a speaker wiring.

Check the indication given at
the micro DAU to determine
which speaker circuit has a
fault. Rectify the wiring fault.

Master
Alarm(s) OC
or SC n

There is an open or short circuit
fault on the master alarm wiring.

Check the wiring and remove
the fault. Ensure the end-of-line
device is connected in the
circuit.

Lost Device

The Device is not communicating
with the Control Panel via the
loop.
Additional 'Sounder' indication
given if it is a micro Distributed
Amplifier Unit or a sounder device

Check the connections to the
device.

Sensor out of
specification

The device indicated is not
functioning correctly.

Device requires maintenance.

21

Vigilon

COMPACT VOICE ALARM

On

Flashing

Fault

Power fault

Fault

Power fault

Fault

Power fault

Fault

Fault

Fault

Sounder

Fault

Sounder

Fault

Sounder

Fault

Summary of Contents for Gent Vigilon Compact













































Reviews:

No comments

Brands by name

Popular brands

Load more brands