Honeywell GENT S4-34410 Data And Installation Download Page 1

Page: 1 / 8

These instructions cover the above interface
modules and accessories. The S4 interface
modules are designed for use with Vigilon and
34000 fire alarm control panel. Each module
includes a loop isolator for device isolation.
Each interface module use one of 207 available
device addresses on a loop and responds to
regular polls from the control panel reporting the
type of device and the status (open/normal/short) of
its supervised input circuit(s).

Features

Analogue addressable communications

Built-in type identification automatically identifies
these devices to the control panel

Reliable communication technique with high
noise immunity

Soft or SAFE addressing

Common mounting options including surface
mount, panel mount and DIN rail mount

Dual-colour LEDs

Plug-in terminal connections for ease of field
wiring

EN54-17:2005 and EN54-18:2005

Cables

The cables recommended for wiring the input /
output lines are the same as those used for loop
wiring, see instructions supplied with the fire control
panel.

Installation

The S4 interface modules can be mounted in other
equipment housings using the DIN rail mount
brackets (S4-34491). A module can also be fitted
into a plastic box (S4-34490) or metal box
(S4-34492). The boxes have cable termination
points on the enclosure for incoming cables.

4188-873_issue 4_Pt.1_02/09_S4 LV Interfaces

Data and Installation

Interface Modules for Vigilon

Low voltage (LV) Input/Output

by Honeywell

S4-34410

S4 1-Input Interface
Module
(low voltage)

S4-34420

S4 1-Output &
1-Input Interface
Module (low voltage)

S4-34450

# S4 4-Input / Output
Interface Module
(low voltage)

Channel

Input

COM

Output

S4-34490

Plastic box

1- End-of-line
Capacitor unit

2- 10K Resistors

1- End-of-line
Capacitor unit

8- 10K Resistors

S4-34491

DIN rail mount
bracket

# Now supplied fully assembled

1- Allen key

2 - M4 Screws

S4-34492

Metal box

2 - M4 Posi Pan Screws
7 - Hole plugs

Module

DIN rail mount bracket

Slide &
lock

Hook and push
to lock

DIN rail

Connect to loop

cable screen

Allen
key

Box

Module

M4 Screws

Door

106

62.5

3 - box fixing points
(Includes 1-keyhole)

7 - top cable
entry points

Module

M4 Screws

Lid

140

Metal
backbox

7 usable cable entry points

Summary of Contents for GENT S4-34410









Search results

Summary of Contents for GENT S4-34410

Reviews:

Honeywell GENT S4-34410, Data And Installation, Page: 1 / 8

Search results

Summary of Contents for GENT S4-34410

Reviews: