Honeywell Genesis 7580G User Manual Download

Page: 103 / 202

6 - 23

UPC-E0 Addenda Separator

When this feature is

, there is a space between the data from the bar code and the data from the addenda. When turned

Off

, there is no space.

Default = On.

UPC-E0 Check Digit

Check Digit specifies whether the check digit should be transmitted at the end of the scanned data or not.

Default = On.

UPC-E0 Leading Zero

This feature allows the transmission of a leading zero (0) at the beginning of scanned data. To prevent transmission, scan

Off

Default = On.

UPC-E0 Addenda

This selection adds 2 or 5 digits to the end of all scanned UPC-E data.

Default = Off for both 2 Digit and 5 Digit Addenda.

* On

Off

* On

Off

* On

Off

2 Digit Addenda On

* 2 Digit Addenda Off

Summary of Contents for Genesis 7580G











































































































































































































Search results

Summary of Contents for Genesis 7580G

Reviews:

Related manuals for Genesis 7580G

Brands by name

Popular brands

Honeywell Genesis 7580G, User Manual

Search results

Summary of Contents for Genesis 7580G

Reviews:

Related manuals for Genesis 7580G

Brands by name

Popular brands