14
FL-PS Series Instruction Manual —
P/N LS10227-001FL-E:B 3/29/2021
Installation
Addressable Module Mounting
2.3 Addressable Module Mounting
The FL-PS has been designed to allow the mounting of an addressable control, relay, or monitor module on the main circuit board inside
the power supply cabinet. This allows power to be fed from an FL-PS output circuit directly to the module, if needed, without running
the power wires outside the cabinet. Remove mounting screws from the positions indicated below and replace with standoffs (included
in hardware kit). Mount the module over the standoffs and secure with screws.
Compatible modules include the CMF-300(A), MDF-300(A), MMF-300(A), CRF-300(A), CDRM-300, CMF-300-6(A), CRF-300-
6(A), and MMF-300-10(A).
NOTE:
PS-MOUNT, the optional hardware kit, ordered separately, contains all necessary hardware for mounting the ZNAC-PS onto the
PCB with an additional multi-point module.
TB4
TB15
T
B
2
T
B
1
O
U
T
6
O
U
T
5
O
U
T
4
O
U
T
3
O
U
T
2
O
U
T
1
NAC1
AUX1
NAC2
AUX2
O
U
T
6
O
U
T
5
O
U
T
4
O
U
T
3
O
U
T
2
O
U
T
1
NAC1
AUX1
NAC2
AUX2
*If the SLC device does
not match the one in this
figure, refer to the SLC
manual wiring conver-
sion charts for legacy
and newer versions of
the modules.
Figure 2.4 Mounting a Single Module in the FL-PS Cabinet
Install stacked standoffs
(0.5” + 1.093” M/F)
– +
–
+
– +
–
+
– +
–
+
– +
–
+
– +
–
+
–
+
–
+
T1
0
J1
BA
SE
AD
DR
ES
S+
0
BA
SE
AD
DR
ES
S+
1
BA
SE
AD
DR
ES
S+
2
BA
SE
AD
DR
ES
S+
3
BA
SE
AD
DR
ES
S+
4
BA
SE
AD
DR
ES
S+
5
SW
1
T1
+1
+0
+2
+3
+4
+5
T0
T2
T3
T4
T5
T1
1
T1
2
T1
3
T1
4
T1
5
T1
6
0
1
2
3
4
5
6
7
8
9
1
0
1
1
1
3
1
4
1
5
1
2
0
1
2
3
4
5
6
7
8
9
AC1 AC2
TB
4
TB15
T
B
3
T
B
2
T
B
1
O
U
T
6
O
U
T
5
O
U
T
4
O
U
T
3
O
U
T
2
O
U
T
1
O
U
T
6
O
U
T
5
O
U
T
4
O
U
T
3
O
U
T
2
O
U
T
1
install 1.093” M/F
standoffs
Note: For instructions on mounting a multi-module and a ZNAC-PS module, refer
to the
ZNAC-PS Install Sheet #LS10228-000GE-E.
The multi-module
must
be installed upside down when the ZNAC-PS is installed. If
the ZNAC-PS is
not
installed, the multi-module may be mounted in either direction.
Figure 2.5 Mounting a Multi-Module in the FL-PS Cabinet
