Honeywell Fire-Lite Alarms ECC-125DA Installation Manual Download | Manualshive

Page: 29 / 38

background image

ECC-50/125DA Instruction Manual —

P/N LS10027-000FL-E:D 5/21/2015

29

Installation

ECC-50BDA Backup Remote Amplifier

3.2.3 Installing the Optional ECC-50WBU

The ECC-50WBU provides backup capability when the ECC-50BDA is set for the 100 watt mode
with backup.

The ECC-50WBU mounts onto the ECC-50BDA board with the standoffs provided. Figure 3.3
shows the location of the ECC-50WBU on the ECC-50BDA board.

To install the ECC-50WBU,

1. Make sure that all power supplied to the ECC-50BDA has been removed.
2. Insert the supplied M/F standoffs in the locations shown below.
3. Connect the backup amplifier cable harness (P/N 50116775-001) to the connector labeled

“Backup Amplifier” on the ECC-50BDA.

4. Lay the ECC-50WBU over the standoffs installed in step 2 and secure with supplied screws.
5. Connect the other end of the cable harness to the header on the ECC-50WBU.

Figure 3.3 Installing the ECC-50WBU onto the ECC-50BDA

ECC-50WBU

screw and standoff

locations

connector cable
(P/N 50116775-001)

eccdu

a

l5

0da

BU

.w

m

f

connector pins

firealarmresources.com

«
...
27
28
29
30
31
...
»

Summary of Contents for Fire-Lite Alarms ECC-125DA







































Reviews:

No comments

Related manuals for Fire-Lite Alarms ECC-125DA

Brand: EAW Pages: 12

Brand: GOODWOOD AUDIO Pages: 4

Brand: McIntosh Pages: 2

Brand: Onkyo Pages: 9

Brand: QUAD Pages: 16

Brand: Work Pro Pages: 18

AVP-A1HDCI - Ultra Reference A/V Network Streaming Preamplifier

Brand: Denon Pages: 132

Brand: RE Audio Pages: 6

1812R Blues King 12

Brand: SUPRO Pages: 8

MULTI-TASKER MT103-118

Brand: Altinex Pages: 11

Brand: Rotel Pages: 5

Brand: Q-tron Audio Pages: 10

XTR Power Amplifier XTR15001

Brand: Orion Pages: 102

VALVESTATE 8008

Brand: Marshall Amplification Pages: 6

Brand: Pyle Pages: 4

Brand: Sound Choice Pro Audio Pages: 13

Brand: Key Digital Pages: 11

Brand: Eminence Pages: 1

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands