Honeywell FF-SB12 Series Installation Manual Download Page 49

Page: 49 / 70

107062-12 EN FR26 GLO 501 Printed in France

IMPROPER SYSTEM PERFORMANCE

Ensure independent stop circuit safety relays have mechanically linked contacts that prevent contact
overlapping in the event of a welded contact.

Failure to comply with these instructions could result in death or serious injury.

IMPROPER INSTALLATION OF FF-SB SERIES LIGHT CURTAIN

Use Figure 3-7 wiring diagram to ensure external relay monitoring of the FF-SB Series Light Curtain.

Failure to comply with these instructions could result in death or serious injury.

Figure 3-7 Wiring Diagram for FF-SB Series configuration (except FF-SB12R02)

NEUTRAL

EARTH

GROUND

(Emitter and Receiver

must be grounded

for proper operation)

POWER

Cycle Start

Signal Beam

Status

FF-SB12, FF-SB14

FF-SB15

Additional output

channel, may be

used to annunciate

to PLC

SUPPLY VOLTAGE

ARC SUPPRESSOR

220 ohm + 0.22 µF

SUPPLY VOLTAGE

EARTH

GROUND

(Emitter and Receiver

must be grounded

for proper operation)

MACHINE CONTROL

SCREW ON

INTERNAL FUSE

0,5 AMP

EMITTER AND
RECEIVER

NEUTRAL

SUPPLY VOLTAGE

●

Jumper Link position
on the Receiver
Power Board (to be
set up before
operation)

RECEIVER

Not
connected

*Two arc suppressors are provided with the light curtain.

Summary of Contents for FF-SB12 Series







































































Search results

Summary of Contents for FF-SB12 Series

Reviews:

Related manuals for FF-SB12 Series

Brands by name

Popular brands

Honeywell FF-SB12 Series, Installation Manual

Search results

Summary of Contents for FF-SB12 Series

Reviews:

Related manuals for FF-SB12 Series

Brands by name

Popular brands