background image

9

Adjustment, Start
and Stop

32-00055—01

In this chapter you will find instructions on how to adjust a
system, and how to start and stop a system. 

  Do not bypass any safety feature. You can cause

fires and explosions.

Step 1: Reset the System

1. Set the air flow switch so that it drops out at 20% below

the maximum pressure of the combustion air blower. 

2. Set the low gas pressure switch at 20% below the gas 

pressure measured at the inlet to the main gas valve 
train.

3. Set the high gas pressure switch at 20% above the gas 

pressure measured at the inlet to the main gas valve 
train.

4. Close all the burner (and by-pass pilot, if applicable) 

gas valves, manual and automatic.

5. Start the combustion air blower.

6. Try to ignite the burner; be sure the flame monitoring 

system indicates a flame failure.

  Make sure blower rotates in the correct direction.

If incorrect, have a qualified electrician rewire the
blower to reverse it.

7. Activate the pressure switches and other limit 

interlocks. Be sure the switches fail as intended in the 
event of a power failure.

  If simulated limits or simulated flame failures do

not shut down the fuel system within the required
failure response time, immediately correct the
problem before proceeding.

8. Adjust main gas inlet pressure to the ratio regulator 

within the range specified in the appropriate datasheet.

  Gas inlet pressures must stay within the specified

range. Pressure above the specified range can
damage the ratio regulator. 

  Pressure below the specified range can impair the

ability of the ratio regulator to control the gas flow. 

  Operating the system outside the specified range

can cause excess fuel consumption and the
possible accumulation of unburned fuel in the
tube.

  In extreme cases, this accumulation of unburned

fuel may cause fires or explosions.

9. With modulating air burners, verify that the actuator 

opens the air BV towards the back of the burner as 
shown. If it doesn’t, refer to the actuator’s literature for 
instructions on how to reverse the direction.

Figure 4.1. Air BV

DANGER

CAUTION

DANGER

WARNING

Back

Open

Closed

Open in this 

direction only

4

Summary of Contents for Eclipse ImmersoPak IP004





















Reviews: