manualshive.com logo in svg

Honeywell DT92, Manual, Page: 16 / 17

Share
Download
Honeywell DT92 Manual Download Page 16

DT92 WIRELESS DIGITAL ROOM THERMOSTAT

16

To enter Installer Mode: 

a. Put DT92 into off/standby mode by pressing and

holding the 

off/standby

 button for 2 seconds.

b. Now press and hold both 

▲

 and 

▼

 temperature

adjustment buttons for 3 seconds, until the
display shows the word “Inst”.

c. Press 

the 

▲

 button to get to the first parameter

Ot. The parameter code is shown on the display
separated by a colon from the parameter value.

To select and change a parameter: 

d. Use 

the 

▲

 and 

▼

 buttons to move from one

parameter to another.

e. Press 

the 

off/standby

 button to select the

parameter value, ready to change

f.

Use 

the 

▲

 and 

▼

 buttons to adjust the

parameter value. When the correct value is
flashing, confirm the selection by pressing the

off/standby

 button again, returning to the

parameter menu.

To exit Installer Mode: 

g. Press and hold the 

off/standby

 button for 3

seconds

Note: 

Installer Mode will exit automatically after 10 

minutes if no buttons are pressed.

 

INSTALLER MODE - FLOWCHART 

Parameter

Value

ES parameter

Only available 

on DT92E model

Summary of Contents for DT92


















Reviews:

No comments