4
Period
1
2
3
4
Time
.
6:30.
8:00.
18:00.
22:30
Temperature
.
21°C.
18°C.
21°C.
16°C
The Built-in Heating Program
The.built-in.heating.program.has.4.temperature.level.changes.that.can.be.set.between.3.00am.
and.2.50am.the.following.day.-.allowing.you.to.maintain.the.evening.temperature.after.midnight..
Each.temperature.level.can.be.set.between.5°C.and.35°C,.and.adjusted.in.0.5°C.increments..The.
factory.default.program.for.heating.is.as.follows.
Reviewing the Heating Program
To.review.or.edit.the.heating.program.use.the.
PROGRAM
.
.or.
.buttons.to.navigate.between.
the.4.individual.programming.periods.
Modifying the Heating Program
To change the heating program:
a.
. Press. either. of. the.
PROGRAM
.
. or.
. buttons. to.
enter.the.programming.mode..The.time./.temperature.
settings.for.period.
..will.be.flashing.as.shown..The.
active. period. is. highlighted. by. a. flashing. square.
around.the.numbers.at.the.bottom.of.the.screen.
b.
. To.adjust.the.period.start.time.use.the. . .or. .buttons,.the.display.will.stop.flashing.and.the.
‘OK?’.indicator.will.be.displayed..Holding.the.button.down.will.change.the.time.quickly.
.
Note:
If you are pressing the or buttons and the display flashes the next period, it
means the next period will be pushed forward.
c.
. Once.the.required.time.is.reached.press.the.green.
.button.to.confirm.
.
Note:
If the original time setting did not require adjustment press the green
button to move
to step
‘d’
.
d.
. The.temperature.setting.for.period.
.will.now.be.flashing..To.adjust.this.press.the. . .or. .
buttons.and.confirm.the.setting.again.by.pressing.the.green.
.button.
e.
. The.next.time.and.temperature.period.will.now.be.active..Adjust.this.by.repeating.steps.
b
.-.
d
.
above.until.all.4.periods.are.set.or.press.the.
AUTO
button.to.run.the.program.as.set,.at.any.time.
Disabling / Enabling Time Periods
The.thermostat.has.4.periods.that.can.be.programmed,.but.you.may.not.need.all.of.these.switch.
points.for.your.heating.requirements..Therefore,.any.period.from.2.to.4.can.be.removed.from.(or.
returned.to).the.heating.program.profile.
To disable or enable time periods:
a.
. To.disable.unwanted.periods.go.to.the.desired.period.(
.to.
4
)..using.the.
PROGRAM
.
.or.
.
buttons.to.navigate,.ensure.the.correct.period.is.highlighted.with.the.flashing.square.symbol..
Press.and.hold.the. .button.for.at.least.2.seconds.and.the.display.will.indicate.the.period.has.
been.removed.from.the.program.
b.
. To.enable.periods.again.follow.the.same.procedure.as.above,.navigating.to.the.already.disabled.
period..To.enable.this.period.again.press.and.hold.the. .button.for.at.least.2.seconds.
4
‘Efficient Daily Use’
.
PROGRAMMING THE CM701
