background image

EAGLEHAWK Controller 

Installation & 
Commissioning 
Instructions 

 

 
 

® U.S. Registered Trademark 
Copyright © 2016 Honeywell Inc.  •  All Rights Reserved 

 

EN1Z-1005GE51 R0216 

TABLE OF CONTENTS 

Safety Information ................................................................ 2

 

General Safety Information ............................................... 2

 

Information as per EN 60730 ............................................ 2

 

WEEE Directive ................................................................ 2

 

Standards, Approvals, etc. ................................................ 2

 

3rd-Party Software Licenses ............................................... 2

 

Specifications of Controller ................................................. 3

 

System Overview .................................................................. 3

 

Overview of Hardware ...................................................... 3

 

System Architecture .......................................................... 4

 

Bus and Port Connections ................................................ 5

 

Mounting/Dismounting ...................................................... 10

 

Before Installation ........................................................... 10

 

Dimensions ..................................................................... 10

 

Wiring and Set-Up .............................................................. 11

 

General Safety Considerations ....................................... 11

 

Wiring Terminals ............................................................. 11

 

Terminal Assignment ...................................................... 11

 

Power Supply .................................................................. 11

 

RIN-APU24 ..................................................................... 12

 

Lightning Protection ........................................................ 12

 

Engineering, Commissioning ............................................ 13

 

Required Preparations .................................................... 13

 

Behavior of Outputs during Download ............................ 13

 

Extra Parts .......................................................................... 14

 

Software Licenses and Upgrades ..................................... 14

 

Panel Bus Connection ....................................................... 15

 

Overview of Panel Bus I/O Modules ............................... 15

 

Panel Bus Considerations ............................................... 15

 

Connecting EAGLEHAWK via its RS485-1 Interface to a 
Panel Bus ....................................................................... 16

 

Connecting EAGLEHAWK via its RS485-2 Interface to a 
Panel Bus ....................................................................... 17

 

Cable Specifications ....................................................... 18

 

LonWorks Communications ............................................. 19

 

General Information ....................................................... 19

 

Connecting to a L

ON

W

ORKS

 Network .............................. 19

 

BACnet MS/TP Bus Connection ....................................... 20

 

BACnet MS/TP Bus Considerations ............................... 20

 

Connecting EAGLEHAWK via its RS485-1 Interface to a 
BACnet MS/TP Bus ........................................................ 20

 

Connecting EAGLEHAWK via its RS485-2 Interface to a 
BACnet MS/TP Bus ........................................................ 22

 

Modbus Connection .......................................................... 23

 

Modbus Considerations .................................................. 23

 

Connecting EAGLEHAWK via its RS485-1 Interface to a 
Modbus .......................................................................... 23

 

Connecting EAGLEHAWK via its RS485-2 Interface to a 
Modbus .......................................................................... 24

 

M-Bus Connection ............................................................. 25

 

M-Bus Considerations .................................................... 25

 

M-Bus Connection Procedure ........................................ 26

 

Effect of Poll Rate + Subscribed Points on CPU Load ... 27

 

Troubleshooting ................................................................ 28

 

EAGLEHAWK Controller Troubleshooting ..................... 28

 

Panel Bus I/O Module Troubleshooting .......................... 29

 

Appendix 1: Earth Grounding ........................................... 30

 

EAGLEHAWK Systems and SELV ................................. 30

 

EAGLEHAWK Systems and Standard EN60204-1 ........ 30

 

Earth Grounding of EN60204-1 Applicable Systems ...... 30

 

Index ................................................................................... 32

 

 
 
 

Trademark Information

 

LON, L

ON

W

ORKS

, and Neuron are trademarks of Echelon 

Corporation registered in the United States and other 
countries. 

Summary of Contents for CENTRA LINE EAGLEHAWK

































Reviews: