manualshive.com logo in svg

Honeywell ADEMCO LYNXR-I Security System, Installation And Setup Manual, Page: 35 / 72

Share
Download
Honeywell ADEMCO LYNXR-I Security System Installation And Setup Manual Download Page 35

LYNXR-I Installation and Setup Guide

 

 

- 35 - 

✻

80 Device Programming Menu Mode

 

 

STOP

 

The "STOP" programming determines when and under what conditions the device will be de-

activated. The following options are available: 

 

Upon Restore of a Zone List 

Restore Zone List: If a "ZONE LIST" is used as the “Stop” event, the device will de-activate when 

all

 the 

zones in that list restore from a previous fault, trouble, or alarm condition.  This will occur regardless of 
what is programmed to "START" the device; therefore, a "RESTORE ZONE LIST" would normally only be 
used when a "ZONE LIST" is used to start the device. 

 

Upon a Zone Type or System Operation 

Zone Type/System Operation: Instead of using a "RESTORE ZONE LIST," a specific zone (response) type or 
system operation action can be selected to de-activate the device. 

•

 

If a specific "ZONE TYPE" is chosen,

 

any zone of that response type that restores from a previous alarm, 

trouble, or fault condition will cause the device to de-activate. 

•

 

If a "SYSTEM OPERATION" is chosen, that operation will cause the device to de-activate.   

During normal system operation, 

any devices may be manually started by keypad entry of: 

Code* + [#] 

+ 4 + “n;” 

or manually stopped by keypad entry of:

 Code* + [#] + 7 + “n,” 

where “n” = the device number to 

be controlled. 

* Code is required for devices 7 and 8. For devices 1-6, code is not required. See User Manual for more 
information. 

 

Programming Powerline Carrier Devices 

 

While in program mode, press 

✻

80 to enter Output Device Menu Mode.

 This mode is used to program 

all output devices used in the system. Refer to the output device table for 

✻

80 on the separate programming 

form when programming output devices. 

 

Note: 

The House ID of the Powerline Carrier Devices must be entered in data field 

✻

25.

 

 

The prompts for 

✻

80 are as follows: 

 

          80 

Powerline Carrier Device Programming Main Menu prompt 

 
A  01 

Device Number --------- for entering the device number 

 
b  

Device Action ------------ for defining the action the device will perform when active 

 
C 

Start Event Type ------- for assigning the event type to start the action 

 
d 

Start Zone List ---------- for assigning the zone list to start the action 

 
E 

Start Zone Type--------- for assigning the zone type to start the action 

 
F 

Stop Zone List ----------- for assigning the zone list to stop the action 

 
1A 

Stop Zone Type---------- for assigning the zone type to stop the action 

 

Summary of Contents for ADEMCO LYNXR-I Security System









































































Reviews:

No comments