background image

 
 
 
 
 

 

 

Page 

2

 of 

8

 

State 

Green LED  Red LED 

Sounder 

Action 

Low Battery 
0-7 days 

Off 

Blinks every 

45 seconds 

Off 

The battery power is low. ADT has 
been contacted. You will be notified of 
the non-emergency situation. Replace 
the battery. Please refer to the 

Smoke 

and Heat Detector Battery 
Replacement

 page. 

Low Battery 
8+ days 

Off 

Blinks every 

45 seconds 

Chirp every 
45 seconds  

The battery power has been low for 8 
or more days. Press the Test switch to 
silence the chirp for 12 hours. ADT has 
been contacted. You will be notified of 
the non-emergency situation. Replace 
the battery immediately. Please refer 
to th

Smoke and Heat Detector 

Battery Replacement

 page.  

Power Up 

Blinks every 

5 seconds 

Blinks every 

5 seconds 

Off 
 
 

The device is powering up. The lights 
will blink for approximately 20 seconds 
until the unit has completed the power 
up cycle. 

Out of 
Sensitivity 

Off 

Blinks every 

5 seconds 

Off 
 
 

A problem has been detected with the 
smoke detector. The smoke detector 
compensates for long term changes in 
the environment resulting from dust 
and other factors. This automatic 
compensation sensitivity needs to be 
reset by a technician. Please refer to 
the 

Contact Us

 page 

 
 
 
 

DSC WS4916  

 
These trouble conditions apply to the 

DSC WS4916

 wireless 

smoke detector. This detector has one LED light and a sounder 
to indicate the detector’s status. 
 

 

 
 
 

State 

LED 

Sounder 

Alarm Mode 

Action 

Normal 
(standby) 

Blinks every 

50 seconds 

Off 
 
 

None 

The device is operating normally. 
No action needed. 

Summary of Contents for Ademco 5806 W3









Reviews: