background image

12

ACUIX IP Rugged Housing and Dome

Recommended Wiring

Power Requirements

The outdoor ACUIX requires a 24 VAC power supply @ 2.6 A, measured at the dome.

Refer to 

Table 1-3

 and 

Table 1-4

 to determine the wire sizes and maximum distances for 

one power source for one ACUIX and the required power supplies for CE compliance.

Table 1-2

ACUIX IP Recommended Wiring

Type

Recommended Cable

Maximum Distance

Ethernet

CAT5 or above

328 feet (100 meters)

Power

18 AWG 2-Conductor, Vinyl 
Jacket

See gauge chart for each 
unit

Alarm

20 gauge unshielded twisted 
pair

10,000 feet (348 meters)

Table 1-3

Wire Gauge Required for Maximum Distance to Dome

AWG

24 VAC Camera plus Heater & Blower (2.6 A)

22

29 feet (8.8 meters)

20

45 feet (13.7 meters)

18

72 feet (21.9 meters)

16

115 feet (35.1 meters)

14

183 feet (55.8 meters)

12

291 feet (88.7 meters)

Table 1-4

Power Supplies

Model Number

Description

HPTV2404

4 Output, 24 VAC, 4A

HPTV2404CB

4 Output, 24 VAC, 4A, PTC

HPTV2404WP

4 Output, 24 VAC, 4A. NEMA4X Weatherproof enclosure

HPTV2404WP-2

4 Output, 24 VAC, 8A, NEMA4X Weatherproof enclosure

HPTV2401S

Single Output, 24 VAC, 8A, Indoor (includes power and video 
surge suppression)

HPTV2401Z

Single Output, 24 VAC, 8A, Indoor (includes power, video, and 
data surge suppression)

HPTV2401WPS

Single Output, 24 VAC, 8A, Weatherproof (includes power and 
video surge suppression)

HPTV2401WPZ

Single Output, 24 VAC, 8A, Weatherproof (includes power, video, 
and data surge suppression)

Summary of Contents for Acuix IP Series

























Reviews: