manualshive.com logo in svg

Honeywell 5496, Installation And Operation Manual, Page: 23 / 34

Share
Download
Honeywell 5496 Installation And Operation Manual Download Page 23

151276-L8

A-1

Appendix A
Compatible Devices

For proper operation, you must use polarized devices with a Model 7628 4.7k ohm EOL 
resistor on each circuit. All supervised notification appliances used with the 5496 must be 
polarized.

A.1

Notification Appliances

Note: Not all devices can use the Sync feature, be sure to check A.1 to ensure the device you have chosen will 

work with this feature. This control is UL listed for single circuit synchronization.

Table A-1 below lists notification appliances compatible with the fire alarm control panel. 
Appliances which can be synchronized indicate the type of sync available in the columns 
marked Audio and/or Visual

Table A-1: Compatible Notification Appliances

Manufacturer

Model

Audio

Visual

Type

AMSECO

SH24W-153075

x

x

Horn/Strobe

SAD24-153075

x

Strobe

SAD24-75110

x

Strobe

SL24W-75110

x

Strobe

SL24C-3075110

x

Strobe

SLB24-75

x

Strobe

RSD24-153075

x

Strobe

RSD24-75110

x

Strobe

SH24W-75110

x

x

Horn/Strobe

SH24W-3075110

x

x

Horn/Strobe

SHB24-75

x

x

Horn/Strobe

SCM24W-153075

x

Chimes/Strobe

SCM24W-75110

x

Chimes/Strobe

SCM24C-3075110

x

Chimes/Strobe

SCM24C-177

x

Chimes/Strobe

H24W

x

Horn

H24R

x

Horn

Summary of Contents for 5496



































Reviews:

No comments