Honda SSBL Instruction Manual Download Page 31 | Manualshive

Page: 31 / 36

background image

31

Insert the pipe cap [2] into the shaft

tube [1].

Put on gloves before cleaning.

Clean the attachment. Wipe off the dirt or stain with a cloth, etc.

Store the blower in the following place.

(a)  Locked place
(b)  High place out of reach of children and other unauthorized person
(c)  Dried and cool dark place

[2]

[1]

4

5
6
7

«
...
29
30
31
32
33
...
»

Summary of Contents for SSBL





































Reviews:

No comments

Related manuals for SSBL

Brand: Gardenline Pages: 16

HLG 650-2000 LCD

Brand: Gude Pages: 48

Brand: Poulan Pro Pages: 40

Brand: Grizzly Tools Pages: 104

Brand: Nakayama Pages: 19

Brand: Tennant Pages: 21

Brand: QGarden Pages: 20

Brand: LEHR Pages: 20

Brand: Yardworks Pages: 10

Brand: Gardebruk Pages: 14

STRATO-CHARGED EBZ4800

Brand: Zenoah Pages: 16

Brand: Murray Pages: 171

C950-52846-0 9.0 T.P.

Brand: Craftsman Pages: 110

Brand: Craftsman Pages: 92

Brand: Husqvarna Pages: 24

Brand: Husqvarna Pages: 44

Brand: Husqvarna Pages: 32

Brand: Husqvarna Pages: 32

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands