background image

3

Important Cautions for Safe Work

 

● NIKKARI Co., Ltd. (hereinafter referred to as NIKKARI) cannot foresee all the risks in handling the 

blower. Therefore, also give consideration to general safety measures not stated in this manual, 
powerhead manual to prevent accidents when handling the blower.

 

● The blower is a tool with a fan which is rotating at high speed to generate high-speed wind. To 

decrease risk of personal injury, special safety precautions must be observed. If it is used carelessly or 
inappropriately, scattered pieces of stones or sands could hit your eyes or body, which may result in a 
serious accident such as sight loss.

Important Cautions for Instruction Manual

 

● This instruction manual is copyrighted and all rights are reserved. This instruction manual, in whole or 

part, may not be copied, translated or reproduced to any electronic medium or machine readable without 
prior written consent from NIKKARI.

 

● The contents described in this instruction manual and powerhead manual are subject to change without 

prior notice.

 

● Illustrations or figures shown in this instruction manual may partially differ from your blower attachment.

 

● In case of hand over or rent of the blower, instruct to have a good understanding of the contents of this 

instruction manual and powerhead manual before starting any work. Be sure to submit this manual and 
the manual of the powerhead to which the attachment is installed to the customer.

 

● If this instruction manual or powerhead manual is lost or damaged, order from sales agency 

immediately.

 

● If you have any questions about descriptions in this manual or powerhead manual, contact the sales 

agency.

Summary of Contents for SSBL





































Reviews: