background image

10 EN

MOWING PROCEDURE

Read the safety instructions before starting to mow.

HYE type:

Always release the cutting-means control lever and the drive 
clutch lever before starting the engine. Starting is more difficult 
when the cutting means is engaged. If drive clutch is engaged, 
the lawnmower will move when the engine is started.

1. Select the suitable forward 

speed with the shift lever [1].

2. Engage the cutting means:

- Press the yellow button [2] 

located on the top of the 
cutting-means control lever 
[3], and at the same time push 
it quickly and hold it against 
the handle.

3. Engage lawnmower forward 

drive when the motor has picked 
up speed:
- The drive clutch lever [4] acts 

as a variable speed control 
according to its squeezed 
position. It makes the speed 
vary between zero and the 
maximal speed preset with the 
shift lever. The maximum 
speed can be reached when 
both levers [3] and [4] are 
pushed forward completely. 
The greater the height of the 
grass to be cut, the more it is 
necessary to reduce the drive 
speed of the machine. This 
will prevent overloading the 
engine and improve the 
quality of the cut.

4. To stop the lawnmower moving forward:

- Release the drive clutch lever [4].

5. To stop the cutting means rotating:

- Release the cutting-means control lever [3].

NOTE:

 It is possible to refrain from using the forward drive while 

mowing in areas with a narrow surface (lanes, borders, etc.).
The drive clutch can be used to move the lawnmower without 
engaging the cutting-means control.

CAUTION:

• Move the cutting-means control lever quickly from one end of its 

travel to the other, so that the cutting means is always either fully 
engaged or fully disengaged. This is to avoid stalling the engine 
and increases the service life of the cutting-means control 
mechanism.

VKE type:

1. With the engine running and 

the cutting means rotating, 
slowly push the Select Drive 
control [5] to propel the mower 
forward.
- Normal operation is with your 

hand comfortably around the 
handle bar and Select Drive 
control. Push the Select 
Drive control with your thumb 
into the indentation for boost 
operation (up a hill, or 
through thick grass).

- You can reduce the ground 

speed by partially releasing 
the Select Drive control.

- Ground speed varies with 

terrain, grass height, slope, 
and grass catcher weight. 
Moving the Select Drive 
control knob [6] or varying 
how far you push the Select 
Drive control forward allows 
you to maintain the desired 
ground speed under 
constantly changing mowing 
conditions.

2. To adjusting the Select Drive control knob [6]:

- The Select Drive control knob allows you to adjust the 

maximum ground speed when the Select Drive control is fully 
engaged. Adjustment is from MIN to MAX.
With the Select Drive control fully engaged:

- MIN will propel the lawnmower at its slowest speed.
- MAX will propel the lawnmower at its fastest speed.

3. To stop the lawnmower moving forward:

- Release the Select Drive control [5].

4. To stop the cutting means rotating:

- Release the cutting-means brake lever [7].

NOTE:

 Releasing the cutting-means brake lever stops the cutting 

means rotating and stops the engine.

SAFETY

C9

C8

C7

SAFETY

[1]

[3]

[4]

[2]

MIN

MAX

[7]

[6]

[5]

MIN

MAX

3RVK87300.book  Page 10  Wednesday, August 8, 2018  11:26 AM

Summary of Contents for HRX476C

























Reviews: