background image

HRS216PKA • HRS216SKA • HRS216VKA

FUEL SYSTEM

7-19

6. EVAPORATIVE EMISSION CONTROL SYSTEM

FUEL TANK CAP

This engine has an EVAPORATIVE EMISSION CONTROL CANISTER built into the fuel tank cap to prevent the 
escape of gasoline vapors into the atmosphere. The cap also contains a ratchet mechanism to provide the operator 
with feedback to indicate that the cap is sealed.

Charging

Gasoline vapor produced in the fuel tank at high ambient 
temperature is absorbed and stored by the charcoal in the 
canister, which is built into the fuel tank cap.

Purging

When the pressure in the fuel tank decreases because of low 
ambient temperature or consumption of gasoline, the air drawn 
through the canister releases the stored gasoline vapor from the 
charcoal. The released gasoline vapor returns to the fuel tank.

FUEL TUBES

Use only low permeation fuel tubes. These fuel tubes have the 
emissions-compliance identification number printed on the tube 
as shown in this example. 

FUEL TANK

This lawn mower has a low permeation, multi-layer fuel tank. If 
the fuel tank is scratched deeply enough that the light gray inner 
liner can be seen, the fuel tank must be replaced.

OUTER 
LAYER

INNER 
LAYER

DEEP
SCRATCH

If the outer layer is scratched deeply enough for the 
light gray inner layer to show, replace the fuel tank.

Summary of Contents for HRS216PKA
























































































































































Reviews: