Honda Harmony II HRR216K1PDA Owner'S Manual Download | Manualshive

Page: 15 / 66

background image

Engine Oil Level

Check the engine oil level with the
engine stopped and the mower on
a level surface.

1.

Remove the oil filler cap, and
wipe the dipstick clean.

2.

Insert and remove the dipstick
without screwing it into the filler
neck. Check the oil level shown
on the dipstick.

3.

If the oil level is low, add the
recommended oil (see page 34)
to reach the upper limit mark on
the dipstick. Do not overfill.

4.

After checking the engine oil
level, screw in the filler
cap/dipstick securely.

FILLER CAP/DIPSTICK

FILLER CAP/
DIPSTICK

UPPER LIMIT

LOWER LIMIT

BEFORE OPERATION

13

«
...
13
14
15
16
17
...
»

Summary of Contents for Harmony II HRR216K1PDA



































































Reviews:

No comments

Related manuals for Harmony II HRR216K1PDA

Brand: MTD Pages: 12

Brand: Toro Pages: 52

Brand: Gardeline Pages: 19

Brand: AL-KO Pages: 652

Brand: Toro Pages: 80

Brand: McCulloch Pages: 10

Brand: MTD Pages: 29

Brand: Yazoo/Kees Pages: 19

GLM 40/124 P EASY

Brand: F.F. Group Pages: 128

Brand: Qualcast Pages: 15

Brand: Weed Eater Pages: 16

Brand: Barbieri Pages: 2

Brand: GGP ITALY SPA Pages: 72

Brand: MTD Pages: 16

Brand: MTD Pages: 28

Brand: Poulan Pro Pages: 48

Brand: Toro Pages: 24

Brand: Cramer Pages: 184

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands