Honda Forza 750 2020 Manual Download

Page: 105 / 211

Shifting Gears

Your vehicle is equipped with an

automatically controlled 6-speed

transmission. It can be shifted automatically

(by AT MODE) or manually (by MT MODE).

Dual Clutch Transmission

In order to respond to rider demands in a

broad range of situations, the transmission is

equipped with three operating modes, AT

MODE (including D mode for regular

operation ); and MT MODE (MT mode for a

6-speed manual operation), which delivers

the same shift feel as a manual transmission.

Always use the recommended tyres and

sprockets to ensure correct Dual Clutch

Transmission operation.

The Dual Clutch Transmission system runs a

self check immediately after starting the

engine.

“ ” appears in the gear position indicator

window for a few seconds, then goes out.

While “ ” appears, you cannot shift into

gear.

20201009081441_32MKV6000_eng_BOOK Page 105 Friday, October 09 2020 08:19:30 JST

Operation Guide

102

N-D switch
A/M switch

MODE

Summary of Contents for Forza 750 2020




















































































































































































































Search results

Summary of Contents for Forza 750 2020

Reviews:

Related manuals for Forza 750 2020

Brands by name

Popular brands

Honda Forza 750 2020, Manual

Search results

Summary of Contents for Forza 750 2020

Reviews:

Related manuals for Forza 750 2020

Brands by name

Popular brands