Honda EU3200i Owner'S Manual Download Page 92 | Manualshive

Page: 92 / 100

background image

90

REFERENCE INFORMATION

“QR Code” is registered trademark of DENSO WAVE INCORPORATED.

The

Bluetooth

word mark and logos are registered trademarks owned by

Bluetooth SIG, Inc., and any use of such marks by Honda Motor Co., Ltd., is under
license. Other trademarks and trade names are those of their respective owners.

Information notice of Bluetooth unit

Unique Identifier
HRM5119

FCC ID
VIYHRM1062

FCC Compliance Statement
This device complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference,
and (2) this device must accept any interference received, including
interference that may cause undesired operation.

Note:
Changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following
measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.

«
...
90
91
92
93
94
...
»

Summary of Contents for EU3200i





































































































Reviews:

No comments

Related manuals for EU3200i

Brand: Icom Pages: 90

Brand: Ford Pages: 24

Brand: Porter-Cable Pages: 22

Brand: Durapac Pages: 11

Brand: Grundig Pages: 16

Brand: Leroy-Somer Pages: 31

Brand: Reflexion Pages: 24

Brand: King Canada Pages: 11

Brand: LENCO Pages: 77

Brand: LENCO Pages: 24

IntelliHeat ST 115

Brand: Pace Pages: 20

Brand: Laser Pages: 20

Brand: Black Diamond Equipment Pages: 12

Brand: DUROMAX Pages: 82

Brand: DUROMAX Pages: 84

IDesign Ultra-Thin Travel Speaker

Brand: Brookstone Pages: 2

Brand: Initial Pages: 36

Brand: PeakTech Pages: 61

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands