Honda EU3200i Owner'S Manual Download

Page: 58 / 100

SERVICING YOUR GENERATOR

AIR CLEANER SERVICE

Foam Air Filter Cleaning

A dirty foam air filter will restrict air flow to the fuel system, reducing engine
performance. If you operate the generator in very dusty areas, clean the foam
air filter more frequently than specified in the Maintenance Schedule.

1. Clean the foam air filter in warm soapy water, rinse, and allow to dry

thoroughly, or clean in nonflammable solvent and allow to dry.

2. Dip the foam air filter in clean engine oil, and then squeeze out all excess oil.

The engine will smoke when started if too much oil is left in the filter.

3. Wipe dirt from inside of the air cleaner cover using a moist rag.

Be careful to prevent dirt from entering the air duct that leads to the fuel
system.

Clean

Squeeze and dry

Dip in oil

Squeeze

Do not twist.

Summary of Contents for EU3200i





































































































Search results

Summary of Contents for EU3200i

Reviews:

Related manuals for EU3200i

Brands by name

Popular brands

Honda EU3200i, Owner'S Manual

Search results

Summary of Contents for EU3200i

Reviews:

Related manuals for EU3200i

Brands by name

Popular brands