Honda EU30is Owner'S Manual Download | Manualshive

Page: 48 / 72

background image

46

FUEL SEDIMENT CUP SERVICE

Gasoline is extremely flammable and is explosive under certain
conditions. Do not smoke or allow flames or sparks in the area.

3.

BREATHER HOSE

6 mm NUTS

6 mm BOLT

AIR CLEANER BASE

The filter prevents dirt or water which may be in the fuel tank from
entering the carburetor. If the engine has not been run for a long time,
the filter should be cleaned.

Turn the engine switch to the STOP position.
Turn the fuel valve lever to the OFF position.
Open the left side maintenance cover.
Remove the air cleaner cover and paper element (see page

and

).

Disconnect the breather hose from the air cleaner base.
Remove the 6 mm bolt and two 6 mm nuts, and remove the air
cleaner base.

6.

5.

2.
3.
4.

1.

44

45

08/10/21 20:26:37 32ZT7702_048

«
...
46
47
48
49
50
...
»

Summary of Contents for EU30is









































































Reviews:

No comments

Related manuals for EU30is

Brand: Tabor Pages: 111

Brand: Q Acoustics Pages: 7

Brand: Z3 Technology Pages: 18

HDMI Super Booster Plus

Brand: Gefen Pages: 10

Brand: Mitsubishi Pages: 12

MAX 175KTL3-X HV

Brand: Growatt Pages: 37

Brand: POWER ON BOARD Pages: 13

Brand: StarTech.com Pages: 4

Brand: Daihen Pages: 158

Brand: Uhlenbrock Elektronik Pages: 4

Brand: AV Access Pages: 20

Brand: Sumitomo Drive Technologies Pages: 30

MagneW Plus+ MGG14C

Brand: Azbil Pages: 110

Multi-Decoder MD-2

Brand: tams elektronik Pages: 40

Brand: Advent Pages: 110

Brand: tams elektronik Pages: 28

Brand: SHOWTEC Pages: 16

NX Distributed Intelligence NX MEDIA CONVERTER

Brand: Hubbell Pages: 3

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands