Honda EU2000i Companion Owner'S Manual Download Page 59 | Manualshive

Page: 59 / 75

background image

57

INITIAL USE INSTRUCTIONS

ADDING ENGINE OIL

WITHOUT OIL

Do not overfill the engine with oil.

COVER SCREW

MAINTENANCE COVER

OIL FILLER CAP/DIPSTICK

UPPER LIMIT

The generator is shipped

in the engine.

With the generator in a level position, remove the oil filler cap/
dipstick.

If the engine is overfilled, the

excess oil may be transferred to the air cleaner housing and air filter.

Screw in the oil filler cap/dipstick securely.

Reinstall the maintenance cover.

Add enough SAE 10W-30 API service classification SJ or later (or
equivalent) oil to bring the oil level to the upper limit of the oil filler
neck. SAE 10W-30 oil is recommended for general use; for
additional recommendations, see page

Loosen the cover screw and remove the maintenance cover.

Place the generator on a level surface.

1.

2.

3.

4.

5.

6.

06/12/21 09:22:22 31Z07602_058

«
...
57
58
59
60
61
...
»

Summary of Contents for EU2000i Companion












































































Reviews:

No comments

Related manuals for EU2000i Companion

Brand: Canon Pages: 115

Brand: Panasonic Pages: 16

Brand: T-Tech Pages: 38

Brand: 7AMEnfant Pages: 2

Brand: AbleNet Pages: 9

Brand: BAC Pages: 10

Brand: Baby’s Journey Pages: 2

Brand: DBI SALA Pages: 32

Brand: Hach Pages: 148

Brand: SALSA Pages: 2

BEA LZR-WIDESCAN

Brand: Halma Pages: 12

Brand: Omega Engineering Pages: 2

Brand: Oki Pages: 52

Brand: Tao Motor Pages: 3

Brand: Vello Pages: 30

Brand: Waterpik Pages: 2

Legend G3 738 NGK

Brand: Valor Pages: 6

Brand: Fantec Pages: 5

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands