Honda CBR1000RR Fireblade 2021 Manual Download Page 163

Page: 163 / 239

Side Stand

Checking the Side Stand

Check that the side stand operates

smoothly. If the side stand is stiff or

squeaky, clean the pivot area and

lubricate the pivot bolt with clean grease.

Check the spring for damage or loss of

tension.

Sit on the vehicle, shift the transmission to

Neutral, and raise the side stand.

Start the engine, pull the clutch lever in,

and shift the transmission into gear.

Lower the side stand all the way. The

engine should stop as you lower the side

stand. If the engine doesn't stop, have

your vehicle inspected by your dealer.

20200219171806_31MKR6000_enu_BOOK Page 164 Wednesday, February 19 2020 17:28:26 JST

Maintenance

161

Side stand

spring

Summary of Contents for CBR1000RR Fireblade 2021
















































































































































































































































Search results

Summary of Contents for CBR1000RR Fireblade 2021

Reviews:

Related manuals for CBR1000RR Fireblade 2021

Brands by name

Popular brands

Honda CBR1000RR Fireblade 2021, Manual

Search results

Summary of Contents for CBR1000RR Fireblade 2021

Reviews:

Related manuals for CBR1000RR Fireblade 2021

Brands by name

Popular brands