Honda CB650F Owner'S Manual Download Page 92

Page: 92 / 123

Tyre Puncture

Removing Wheels

continued

ou
bles

hoo

ting

When removing and installing the wheel, be
careful not to damage the wheel speed
sensor and pulser ring.

❙

Front Wheel

Removal

Park on a firm, level surface.

Cover both sides of the front wheel and
brake calipers with protective tape or
cloth.

On the right side, remove the mounting
bolts and remove the brake caliper.

On the left side, remove the mounting
bolts and remove the brake caliper.

Support the brake calipers so that it
doesn’t hang from the brake hose. Do
not twist the brake hose.

Avoid getting grease, oil, or dirt on the
disc or pad surfaces.

Do not pull the brake lever while the
brake caliper is removed.

Take care to prevent the brake caliper
from scratching the wheel during
removal.

CB650FA only

Left side

Right side

Wheel speed

sensor

CB650FA only

Pulser ring

CB650FA only

Mounting bolts

Tape or cloth

Brake calipers

14 CB650F FA (NK)-32MJED000.book 89 ページ２０１３年１２月２３日　月曜日　午後６時２分

Honda CB650F Owner's Manual

http://www.motorcycle.in.th

Summary of Contents for CB650F




























































































































Search results

Summary of Contents for CB650F

Reviews:

Related manuals for CB650F

Brands by name

Popular brands

Honda CB650F, Owner'S Manual

Search results

Summary of Contents for CB650F

Reviews:

Related manuals for CB650F

Brands by name

Popular brands