Honda CB650F Owner'S Manual Download Page 61

Page: 61 / 123

Maintenance

Removing & Installing Body Components

Seat

❙

Removal

Insert the ignition key into the seat lock,
and turn and hold the key clockwise to
unlock the seat.

Pull the rear of the seat back and up.

❙

Installation

Insert the front and rear prongs into the
front and rear stays on the frame.

Push forward and down on the rear of the
seat until it locks in place.
Make sure that the seat is locked securely
in position to pull it up lightly.

The seat locks automatically when installed.
Take care not to lock your key in the
compartment under the seat.

Front
Prong

Rear stays

Rear Prongs

Seat

Seat lock

Ignition key

Front stay

14 CB650F FA (NK)-32MJED000.book 58 ページ２０１３年１２月２３日　月曜日　午後６時２分

Honda CB650F Owner's Manual

http://www.motorcycle.in.th

Summary of Contents for CB650F




























































































































Search results

Summary of Contents for CB650F

Reviews:

Related manuals for CB650F

Brands by name

Popular brands

Honda CB650F, Owner'S Manual

Search results

Summary of Contents for CB650F

Reviews:

Related manuals for CB650F

Brands by name

Popular brands