background image

CAR CARRIER LOADING AND TRANSPORTING:

Special Precautions:

• 

Car carrier equipment is the only method the manufacturer provides for loading and transporting this 
vehicle. Using other towing equipment will result in possible damage to the vehicle.

  
• 

This vehicle has a low profile. Ramping and extreme care must be used to avoid damage to the front 

and rear lower panels. The front diffuser is easily damaged, so all contact should be avoided when 

loading and unloading.

• 

When loading or winching, DO NOT USE HOOKS OF ANY TYPE ON THE LOWER CONTROL 
ARMS OR ANY OTHER STEERING OR SUSPENSION COMPONENT.  Carefully follow the 

loading procedures specified on the following pages.

• 

USE ONLY WHEEL STRAP TIE-DOWNS to secure this vehicle when transporting.  The use of 
chains or hooks will damage under-vehicle components. Straps through the wheels may result in 
damage.

• 

There is NOT an override provision to get the transmission into 

N

eutral should there be a failure in 

the system. When 12 volt battery power cannot be restored to the vehicle, the front wheels will roll 
freely and rear wheels will remain locked. 

• 

In an emergency situation where the vehicle will not roll or must be moved for towing access, 
wheel-jacking equipment, such as GoJaks or tire skates are recommended. Liquid soap should be 
used to help reduce traction if skates are needed to move the vehicle.

7

Summary of Contents for Acura NSX 2017













Reviews: