Honda 2004 CB600F 599 Owner'S Manual Download Page 177 | Manualshive

Page: 177 / 247

background image

RIGHT FRONT

(4)

(3)

(3) axle pinch bolts
(4) axle bolt

168

If You Have a Flat Tire

Taking Care of the Unexpected

Raise the front wheel off the ground by
placing a support block under the
engine.

Loosen the right and left axle pinch
bolts ( ) and remove the axle bolt ( ).

Remove the fixing bolts ( ) and
remove the right and left caliper
assemblies ( ) from the fork legs.

To avoid damage to the brake hose
during removal, support the caliper
assembly so that it doesn’t hang from
the hose. Do not twist the brake hose.
Avoid getting grease, oil, or dirt on
the disc or pad surfaces. Any
contamination can cause poor brake
performance or rapid pad wear after
reassembly.

4.

1

2.

3.

3

4

2

03/04/26 13:56:44 31MBZ600_177

«
...
175
176
177
178
179
...
»

Summary of Contents for 2004 CB600F 599
























































































































































































































































Reviews:

No comments

Related manuals for 2004 CB600F 599

Brand: Bajaj Auto Pages: 38

Brand: probrake Pages: 2

Brand: hepco & becker Pages: 4

Stealth Air Cleaner Kit

Brand: S&S Cycle Pages: 4

Brand: Ducati Pages: 77

TorqDrive Clutch Pack

Brand: Rekluse Pages: 18

SCARABEO 100 4T - 06-2001 PART6

Brand: APRILIA Pages: 6

Brand: MOTO GUZZI Pages: 12

Intruder VS1400

Brand: Suzuki Pages: 291

Brand: Norton Pages: 69

Brand: Malaguti Pages: 292

Brand: RIEJU Pages: 72

Brand: Benelli Pages: 13

Brand: Abus Pages: 18

Brand: Petzl Pages: 4

Brand: Baja Pages: 8

Brand: Honda Pages: 185

Brand: Qingqi Pages: 39

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands