HONDA marine BF25D Owner'S Manual Download Page 25

Page: 25 / 141

CONTROLS AND FEATURES

LRG, SRT and LRT Types

[standard equipment (LRTC

type)]

[optional equipment (LRGA,

SRTA and LRTA types)]

For panel-mount or top-mount remote

control information, refer to the

instructions provided with the remote

control equipment.

Ignition Switch

The ignition switch controls the

ignition system and the starter motor.

Turning the ignition switch key to the

START position operates the starter

motor. The key automatically returns

to the ON position when released

from the START position.

The engine will not start unless the

gearshift/throttle control lever is in

the N (neutral) position (p. 49) and

the emergency stop switch clip is in

the emergency stop switch.

Turning the ignition switch to the

OFF position stops the engine.

Emergency Stop Switch Clip and

Emergency Stop Switch

OFF

ON START

IGNITION

SWITCH

EMERGENCY

STOP SWITCH

EMERGENCY STOP

SWITCH CLIP

EMERGENCY

STOP SWITCH

EMERGENCY STOP

SWITCH CLIP

EMERGENCY

STOP SWITCH

LANYARD

EMERGENCY STOP

SWITCH CLIP

EMERGENCY

STOP SWITCH

LANYARD

31ZW26430.book Page 23 Monday, November 19, 2018 4:42 PM

Summary of Contents for BF25D












































































































































Search results

Summary of Contents for BF25D

Reviews:

Brands by name

Popular brands

HONDA marine BF25D, Owner'S Manual

Search results

Summary of Contents for BF25D

Reviews:

Brands by name

Popular brands