manualshive.com logo in svg

HONDA marine BF135A, Shop Manual, Page: 25 / 49

Share
Download
HONDA marine BF135A Shop Manual Download Page 25

5-22

• ECT Sensor 1 Troubleshooting

DTC 6-1: ECT sensor 1 voltage is low

1. Symptom reproduction test

-1. Connect the Dr. H and clear the DTC once. If the

DTC can not be cleared, go on the troubleshooting.

-2. Turn the ignition switch ON.
-3. Check the ECT sensor 1 voltage using the Dr. H.

Is the measurement 0.23 – 3.15V?
YES – Temporary failure (Disappeared)
NO – Perform “2. ECT sensor 1 line short circuit

check”.

2. ECT sensor 1 line short circuit check

-1. Turn the ignition switch OFF and disconnect the

ECM connector B.

-2. Check for the continuity between the No. 2

(Red/White) terminal of the ECT sensor 1 harness
side 2P connector and the body ground.

Is there the continuity?
YES – Repair short in the wire between the ECM

and the ECT sensor 1.

NO – Perform “3. ECT sensor 1 check”.

3. ECT sensor 1 check

-1. Turn the ignition switch OFF and connect the Dr. H.
-2. Turn the ignition switch ON. Check the engine

coolant temperature with the Dr. H.

Is the engine coolant temperature normal?
YES – Substitute a known-good ECM and recheck.
NO – Replace the ECT sensor 1 and recheck.

DTC 6-2: ECT sensor 1 voltage is high

1. Symptom reproduction test

-1. Connect the Dr. H and clear the DTC once. If the

DTC can not be cleared, go on the troubleshooting.

-2. Turn the ignition switch ON.
-3. Measure the ECT sensor 1 voltage using the Dr. H.

Is the measurement 0.23 – 3.15V?
YES – Temporary failure (Disappeared)
NO – Go to the step 2.

2. ECT sensor 1 line check

-1. Turn the ignition switch OFF and disconnect the ECT

sensor 1 connector.

-2. Turn the ignition switch ON. Measure the voltage

between the No. 2 (Red/White) and the No. 1
(Green/Red) terminals of the ECT sensor 1 harness
side 2P connector.

Is the measurement 4.30 – 5.25V?
YES – Perform “4. ECT sensor 1 check”.
NO – Perform “3. ECT sensor 1 signal line open

circuit check”.

3. ECT sensor 1 line open circuit check

-1. Turn the ignition switch ON. Measure the voltage

between the No. 2 (Red/White) terminal of the ECT
sensor 1 harness side 2P connector and the engine
ground.

ECT SENSOR 1 HARNESS
SIDE 2P CONNECTOR

TE (RED/WHITE)

VIEWED FROM THE
TERMINAL SIDE

ECT SENSOR 1 HARNESS
SIDE 2P CONNECTOR

VIEWED FROM THE
TERMINAL SIDE

SG2
(GREEN/RED)

TE (RED/WHITE)

ECT SENSOR 1 HARNESS
SIDE 2P CONNECTOR

VIEWED FROM THE
TERMINAL SIDE

TE (RED/WHIT)

Summary of Contents for BF135A


















































Reviews:

No comments