manualshive.com logo in svg

Hommy HM116T, Manual

Share
Download
Hommy HM116T Manual Download Page 3

3

Note:

The following steps should be carried out by professional repair technicians.

When phase reversal happens on power supply, two of the live wires”L1” and “L” should
be exchanged to install.

Important note:

Violating the safety regulations may result in heavy

casualties. Failure to comply with this warning will damage the machine and

its components. Component damage will increase spending on the spare parts and
maintenance.

Safe operation

Do not operate the ice cream
machine

before

read

the

instructions carefully. Failure to

follow this instruction will cause damage to
the machine or operator.

●Do not operate the ice cream
machine that is improperly
grounded .
●Do not repair the ice cream

machine before disconnect the mains,
otherwise it will cause an electric shock.
Please contact with local agent or find a
professional

repair

personnel

when

necessary.
Failure to follow these instructions could
result in electrical shock or damage to the
machine, please consult the electrician for
the correct operation when you are
confused .

Please do not clean the
machine by the water faucet or
inside machine, otherwise it will

cause a severe shock.

The machine must be placed
on horizontal plane, otherwise
it may cause injury to persons
or damage to machine.

Summary of Contents for HM116T

































Reviews:

No comments

Brands by name

Popular brands

Load more brands