background image

 
incidental damages, such as damage to persons or property are not coverable under this 

warranty, and you should refer to your homeowner's insurance policy as with any other 
outside structure. Note: Some states do not allow the exclusion or limitation of certain 

damages, and in those cases these limitations do not apply.     

 

6. Certification Notice     

 

   

 

This device complies with part 15 of the FCC rules. Operation is subjct to 
the followingtwo conditions:   

   

 

This devuce may not cause harmful interference   

   

This device must accept any interference that may cause undesired 
operation. 

 

 

This equipment has been tested and found to comply with the limits for a class B digital 
device, pursuant to part 15 of the FCC rules. These limits are designed to provide to provide 
reasonable protection against harmful interference in a residential installation. This 
equipment generates, uses and can radiate radio frequency energy and, if not installed and 
used in accordance with the installation. , May cause harmful interference to radio 
communication. However, there is no guarantee that interference

   

Will not occur in a particular installation. if this equipment does cause harmful interference 
to radio or television reception, which can be determined by turning the equipment off and 
on, the user is encouraged to try to correct the interference by one or more of the following 
measures:

   

-Reorient or relocate the receiving antenna

   

-Increase the separation between the equipment and receiver

   

-Connect the equipment into an outlet on a circuit different from that to which the receiver is 
connected

   

-Consult the dealer or an experienced radio / TV technician for help

   

 

You are cautioned that changes or modifications not expressly approved by the party 
responsible for compliance could void your authority to operate the equipment. 

 

 

This device complies with part 15 of the FCC rules. Operation is subject to the following two 
conditions

   

(1)            This device may not cause harmful interference and 

 

(2)            This device must accept any interference received, including interference that may 
cause undesired operation 

 

 

Summary of Contents for HSK-200Z












Reviews: