Homecare 37602 Assembly Instructions Manual Download Page 3

 

Assembly Instructions for Homecare Crib Bed models 37603, 37604 

 

Parts: Hardware: 

 

 

2  End Frames 

12  ¼"-20 x 2" Bolts 

1  Side Rail with Handle  

16  Washers 

1  Non-moving Side Rail 

12  ¼"-20 Nuts 

1  Mattress Pan  

  4  ¼"-20 x 2¾" Bolts 

1  Bottom Frame  

  3  ¼"-20 x 1 ½” Bolts (attached) 

2  Non Locking Casters (attached) 

 

2 Locking 

Casters 

(attached) 

  Tools needed:  2  7/16" Wrenches 

NOTE:  Determine the correct position of the bed in the room before you begin to assemble 
the bed. Choose the location for the head of the bed and the side where the non-moving side 
rail will be located. 

 
1.  Place Mattress Deck on its side on a clean, flat surface. 
 
2.  Attach one End Frame to the Mattress Deck with 2 of the ¼"-20 x 2" bolts, washers and nuts. 

Do not tighten completely. 

Repeat to attach second End Frame.

 

 
3.  Lift Mattress Deck and End Frame to insert the remaining 4  bolts and washers.  Attach nuts.  

Do not tighten completely. 

 
4.  Attach Bottom Frame to End Frame with 2 of the ¼"-20 x 2" bolts, washers and nuts. 
 
5.  Stand the Bed in the upright position 
 
6.  Insert the remaining ¼"-20 x 2" bolts, washers and nuts to secure the Bottom Frame. 
 
7.  Position the  Non-Moving Side Rail on the side of the Bed labeled “Non-Moving Side Rail.”   

Attach with 1/4"-20 x 2¾" bolts.  (Remove these labels after assembly.) 

 
8.  Tighten all bolts starting with the upper right, then lower left and continuing diagonally. Check all 

screw caps for metal shavings which may be created while tightening. Check that Mattress 
Deck and Bottom Frame are square and tightened. 

 
9.  Remove the nuts from the 3 bolts at the center of the side of the Mattress Deck.  Push the bolts 

in until they are flush with the Mattress Deck but do not remove bolts.  Discard nuts. 

 
10. Insert moving Side Rail into track. Hold or prop in fully raised position.   
 
11. Locate lock housing at the bottom of the Side Rail.  Push the 3 bolts back through the Mattress 

Deck and thread into lock housing.  Tighten bolts.  

 
12. Raise and lower Side Rail several times to check operation.  Turn the crank at the foot of the 

bed to raise and lower the head of the bed to check operation. 

 
13. Unwrap Mattress and place in Bed.  For Bed accessory installation and model # 37604 Crib Top 

installation, see page 9. 

Summary of Contents for 37602








Reviews: