background image

Please call for replacement parts or assistance:

1-866-942-5362

 

Whalen Storage                  

 

 

   Factory No.: 15548   

      Page #2 of 16 

 

 
 

 
 
 
 
 
 

  

 

 

 
 
 
 

 
 
 
 
 
 

 

 
 
 
 

 

 
 
 
 
 
 
 
 
 
 
 
 
 

 

ASSEMBLY TIPS 

 

Read all instructions BEFORE assembly. 

 

Remove all hardware from box and sort by size. 

 

Check to see that all hardware and parts are present BEFORE assembling. 

 

Ask a friend to assist you with the assembly of this furniture. 

 

To avoid damage, assemble the unit on a sturdy, level and non-abrasive surface. 

 

Please wait until all steps are completed before tightening bolts. 

 

Make sure all bolts are tightly fastened before the unit is used. 

WARNING

Serious or fatal crushing injuries can occur from furniture tip-over.  
To help prevent tip-over: 

 

Place heaviest items in the lowest drawer, shelf. 

 

Do not set TVs or other heaviest objects on the top of this product. 

 

Never open more than one drawer at a time and never allow children to climb or 
hang on drawers, doors, or shelves. 
 

 

Use of tip-over restraints may only reduce, but not eliminate, the risk of tip-over.

 

 

This is a permanent label. Do not attempt to remove! 

M A X I M U M   R E C O M M E N D E D   W E I G H T   L O A D S

 

This unit is intended for use only with the maximum weights 

indicated. Use with products heavier than the maximum weights indicated may 
result in instability causing possible injury. 

TOP MAXIMUM LOAD: 200 LBS. (90.9KG) 

TRAY MAXIMUM LOAD: 15 LBS. (6.8KG) 

DRAWER MAXIMUM LOAD: 12 LBS. (5.5KG) 

HAMPER MAXIMUM LOAD: 100 LBS. (45.5KG) 

Summary of Contents for WSMSL-CTPN

















Reviews: