background image

- 3 -

Step 1: Slide Legs (Part B) through holes in the 

Locking Top Box (Part G) until the bolt holes on 

the Legs align with the holes on the Locking Top 

Box.

Step 2: Insert Long Bolts with Washer from 

Hardware Bag (Part K) through the Holes in the 

legs and use 1 spring washer, 1 washer and a nut 

to fasten. DO NOT TIGHTEN COMPLETELY AT 

THIS TIME. Repeat for all four corners.

Step 3: Repeat steps 1 and 2 for bottom tray 

(Part D). Tighten all hardware completely.

Step 4: Turn Cart upside down as shown in 

Illustration 1

Step 5: Insert Casters (Part I) into holes at the 

bottom of the legs. Make sure to install both 

swivel casters on the same side. Use a Rubber 

Mallet to make sure legs are fully installed.

Step 6: Arrange the Drawer Pieces as shown in 

Illustration 2 *Make sure the lip on part F goes 

under parts E and that the ball bearing slide tab is 

facing upwards, as shown in Illustration 3.

Step 7: Use Short Bolts and 2 Washers from 

Hardware Bag (Part K) on each side to attach 

Both Parts E to Part C. Only attach the bolts on 

the top of these parts and leave the remaining 

holes empty for the next step.

Step 8: Align the holes in the partially assembled 

Drawer with the holes in the Locking Top Box 

(Part G) and use Short Bolts and 2 Washers from 

Hardware Bag (Part K) for each hole.

Step 9: Flip the Cart onto its Casters and 

completely tighten all hardware.

Step 10: Carefully align the Drawer (Part H) with 

the slides and push it into place. Make sure you 

hear clicks to know it is properly aligned.

Step 11: Attach Drawer Handle (Part J) using 4 

Small Screws from Hardware Bag (Part K)

CAUTION: DO NOT FORCE THE DRAWER 

ONTO THE SLIDE RAILS.

This may cause permanent damage to the slide 

roller bearings.

E)

E)

C)

F)

Illustration 1

Illustration 2

Illustration 3

Step 1

Step 2

Step 5

Step 7

Step 8

Summary of Contents for BK05500190













Reviews: