Holtek BS66F340 Manual Download Page 111

Page: 111 / 242

Rev. 1.60

110

August 20, 2019

Rev. 1.60

111

August 20, 2019

BS66F340/BS66F350/BS66F360/BS66F370

Touch A/D Flash MCU with LED Driver

BS66F340/BS66F350/BS66F360/BS66F370

Touch A/D Flash MCU with LED Driver

• CTMnC0 Register

Bit

Name

CTnPAU CTnCK2 CTnCK1 CTnCK0

CTnON

CTnRP2 CTnRP1 CTnRP0

R/W

POR

Bit 7

CTnPAU

: CTMn Counter Pause control

0: Run

1: Pause

The counter can be paused by setting this bit high. Clearing the bit to zero restores

normal counter operation. When in a Pause condition the CTMn will remain powered

up and continue to consume power. The counter will retain its residual value when

this bit changes from low to high and resume counting from this value when the bit

changes to a low value again.

Bit 6~4

CTnCK2~CTnCK0

: Select CTMn Counter clock

000: f

SYS

001: f

SYS

010: f

/16

011: f

/64

100: f

SUB

101: f

SUB

110: CTCKn rising edge clock

111: CTCKn falling edge clock

These three bits are used to select the clock source for the CTMn. The external pin

clock source can be chosen to be active on the rising or falling edge. The clock source

SYS

is the system clock, while f

and f

SUB

are other internal clocks, the details of which

can be found in the oscillator section.

Bit 3

CTnON

: CTMn Counter On/Off control

0: Off

1: On

This bit controls the overall on/off function of the CTMn. Setting the bit high enables

the counter to run while clearing the bit disables the CTMn. Clearing this bit to zero

will stop the counter from counting and turn off the CTMn which will reduce its power

consumption. When the bit changes state from low to high the internal counter value will

be reset to zero, however when the bit changes from high to low, the internal counter will

retain its residual value until the bit returns high again. If the CTMn is in the Compare

Match Output Mode then the CTMn output pin will be reset to its initial condition, as

specified by the CTnOC bit, when the CTnON bit changes from low to high.

Bit 2~0

CTnRP2~CTnRP0

: CTMn CCRP 3-bit register, compared with the CTMn Counter

bit 9 ~ bit 7

000: 1024 CTMn clocks

001: 128 CTMn clocks

010: 256 CTMn clocks

011: 384 CTMn clocks

100: 512 CTMn clocks

101: 640 CTMn clocks

110: 768 CTMn clocks

111: 896 CTMn clocks

These three bits are used to setup the value on the internal CCRP 3-bit register, which

are then compared with the internal counter’s highest three bits. The result of this

comparison can be selected to clear the internal counter if the CTnCCLR bit is set to

zero. Setting the CTnCCLR bit to zero ensures that a compare match with the CCRP

values will reset the internal counter. As the CCRP bits are only compared with the

highest three counter bits, the compare values exist in 128 clock cycle multiples.

Clearing all three bits to zero is in effect allowing the counter to overflow at its

maximum value.

Summary of Contents for BS66F340



















































































































































































































































Search results

Summary of Contents for BS66F340

Reviews:

Holtek BS66F340, Manual, Page: 111 / 242

Search results

Summary of Contents for BS66F340

Reviews: