Holman QT14B Installation And Operation Instructions Manual Download Page 13

 2M-4497-2 10/2010

The foregoing warranty is in lieu of any and all other warranties expressed or implied and constitutes the entire warranty.

FOR ASSISTANCE

Should you need any assistance regarding the Operation or Maintenance of any Star equipment; write, phone, fax or email our Service Department.

In all correspondence mention the Model number and the Serial number of your unit, and the voltage or type of gas you are using.

   ALL:
*

 Pop-Up Toasters

*

 Butter Dispensers

*

 Pretzel Merchandisers

   (Model 16PD-A Only)

*

 Pastry Display Cabinets

*

 Nacho Chip Merchandisers

*

 Accessories of any kind

*

 Sneeze Guards

*

 Pizza Ovens 

    (Model PO12 Only)

*

 Heat Lamps

*

 Pumps-Manual

Visit our Website at: 

www.star-mfg.com 

Email: [email protected]

THOROUGHLY INSPECT YOUR UNIT ON ARRIVAL

This unit has been tested for proper operation before leaving our plant to insure delivery of your unit in perfect condition.  However, there are instances in 
which the unit may be damaged in transit.  In the event you discover any type of damage to your product upon receipt, you must immediately contact the 
transportation company who delivered the item to you and initiate your claim with same. If this procedure is not followed, it may affect the warranty status of 
the unit.

LIMITED EQUIPMENT WARRANTY

All workmanship and material in Star products have a one () year limited warranty on parts & labor in the United States and Canada. Such warranty is limited 
to the original purchaser only and shall be effective from the date the equipment is placed in service. Star's obligation under this warranty is limited to the repair 
of defects without charge, by the factory authorized service agency or one of its sub-agencies. Models that are considered portable 

(see below)

 should be taken 

to the closest Star service agency, transportation prepaid.

>

Star will not assume any responsibility for loss of revenue.

>

On all shipments outside the United States and Canada, see International Warranty.

*

The warranty period for the JetStar six () ounce & Super JetStar eight () ounce series popcorn machines is two () years.

*

  The warranty period for the Chrome-Max Griddles is 

five

 (5) years on the griddle surface. See detailed warranty 

provided

 with unit.

*

   The warranty period for 

Teflon/Dura-Tec

 coatings is one year under normal use and reasonable care.  This warranty does not apply if damage occurs to 

T

eflon/Dura-Tec

 coatings from improper cleaning, maintenance, use of metallic utensils, or 

abrasive

 cleaners, 

abrasive

 pads, product 

identifiers

 and 

point-of-sale attachments, or any other non-food object tha comes in continuous contact with the roller coating.  This warranty does not apply to the  
“non-stick” properties of such materials.

>

This warranty does not apply to "Special Products" but to regular catalog items only. Star's warranty on "Special Products" is six () months on parts  

 

and ninety (0) days on labor.

>

This warranty does not apply to any item that is disassembled or tampered with for any purpose other than repair by a Star Authorized Service Center or    
the Service Center's sub-agency.

>

This warranty does not apply if damage occurs from improper installation, misuse, wrong voltage, wrong gas or operated contrary to the Installation and    
Operating instructions.

>

This warranty is not valid on Conveyor Ovens 

unless

 a 

"start-up/check-out"

 has been performed by a Factory Authorized Technician.

PARTS WARRANTY

Parts that are sold to repair out of warranty equipment are warranted for ninety (0) days. The part only is warranted. Labor to replace the part is chargeable to 
the customer.

SERVICES NOT COVERED BY WARRANTY

PORTABLE  EQUIPMENT

Star will not honor service bills that include travel time and mileage charges for servicing any products considered "Portable" including items listed below.   
These products should be taken to the Service Agency for repair:

1. 

Travel

 time and mileage rendered beyond the 50 mile radius limit

 .

Mileage and travel time on portable equipment 

(see below)

 .

Labor to replace such items that can be replaced easily during a daily cleaning
routine, ie; removable kettles on fryers, knobs, grease drawers on griddles, etc.

 .

Installation of equipment

 

5.  Damages

 due to improper installation

 .

Damages from abuse or misuse

 .

Operated contrary to the Operating and Installation Instructions

 .

Cleaning of equipment

 .

Seasoning of griddle plates

0.

Voltage conversions

.

Gas conversions

.

Pilot light adjustment

.

Miscellaneous adjustments

.

Thermostat calibration and by-pass adjustment

15.  Resetting of circuit 

breakers

 or safety controls or reset buttons

16.  Replacement of bulbs

17.  Replacement of fuses

18.  Repair of damage created during transit, 

delivery,

 &

 

installation OR created by acts of God

*

The Model 

510FD

 Fryer.  

*

The Model 526TOA Toaster 

Oven. 

*

The Model J4R, 4 oz. Popcorn Machine. 

*

 The Model 518CMA & 526CMA Cheese Melter.

*

The Model 12MC & 15MC & 18MCP Hot Food Merchandisers.

*

The Model 12NCPW & 15NCPW Nacho 

Chip/Popcorn

 Warmer.

*

All Hot Dog Equipment 

except Roller Grills & Drawer Bun Warmers.

*

All Nacho Cheese Warmers 

except Model 11WLA Series Nacho Cheese Warmer. 

*

All Condiment Dispensers 

except the Model HPD & SPD Series Dispenser.

*

All Specialty Food Warmers 

except Model 130R, 11RW Series, and 11WSA Series.

*

All 

QCS/RCS

 Series Toasters 

except Model QCS3 & RCS3 Series.

*

All Fast Steamer Models 

except Direct Connect Series.

Summary of Contents for QT14B





















Reviews: