background image

2

XL-FW1114-01 Rev. A

1. Component Part Identification and Specifications

1.1 Identification of Component Parts (Standard Greased FW3510 Shown)

1.2 Important Specifications

Release 
Handle
Spring

Yoke

Lock Jaws

Lock Pin
Grease Fittings

Cam Plate

Adjustment
Bolt and Nut

Grease  
Grooves

Lock Pins

Lock Jaws

Release  
Handle
Lock
Bar

Release
Handle

“Weightsaver”
Mounting Bracket 

"H"

Fifth Wheel Model 

No. **

12

°

min.

12

°

min.

“ISO/DIN”
Mounting Bracket

"H"

Fifth Wheel Model

 No. ** 

FW3510-150

150 kN

20 tonne 

150 mm

FW3510-180

150 kN

20 tonne 

180 mm

FW3510-200

150 kN

20 tonne 

200 mm

15

°

min.

15

°

min.

Max.

 

Fifth Wheel

D-Value

Vertical Load 

Height*

  "H"

FW3510-140

150 kN

20 tonne 

140 mm

FW3510-160

150 kN

20 tonne 

160 mm

FW3510-190

150 kN

20 tonne

190 mm

FW3510-230

150 kN

20 tonne

230 mm

 

* Fifth Wheel Height "H" Does Not Include Mounting Plate Thickness.
** For the low lube version replace the "35" with "34" (i.e. FW3410-150);
 

for the no lube version replace the "35" with "31" (i.e. FW3110-150). 

Max.

 

Fifth Wheel

D-Value

Vertical Load 

Height*

 

* Fifth Wheel Height "H" Does Not Include Mounting Plate Thickness.
** For the low lube version replace the "35" with "34" (i.e. FW3410-150);
 

for the no lube version replace the "35" with "31" (i.e. FW3110-150). 

"H"

Summary of Contents for FW3110









Reviews: