background image

STEP

INSTRUCTIONS

1

Connect the power to the driver and power it on.

You have 1 minute after powering the driver on, to finish 

the next steps. This ensures no accidental inputs or 

reprogramming after installation.

2

Press and hold the “Set” button for 2 seconds > Let go of the “Set”button > 

Press and hold the OFF button “O” for 5 seconds.

The lights will flash after succesfuly clearing the code. 

After the lights have flashed you are able to use all com-

patible remotes.

Code clearing: This ensures everything on the device is reset back to the factory settings. This will ensure that the driver can be 
controlled by any compatible remote control, or paired to a new one. 

Attention: 

For this you will need the remote that comes with the driver. This is the “key” to unlock the driver. The “Code clearing” step will NOT work 

with the Wall Dimmer.

Code learning operation between remote controls: Used to unify system code values or copy a new remote control.

Since each remote control has its own unique RF code at the time of delivery, when there are multiple remote controls in one system, one of them must 

be selected as a main, and other remote controls should copy its RF code.

1.  

Main

 remote control: Press and hold 

“Night light key”

 key for 5 seconds. The indicator of the remote control will flash quickly, means it enters 

 

the pairing code transmission status.

2.  

New

 remote control: Press and hold 

“ON/OFF”

 key for 5 seconds, indicator will flash means it enters learning code status.

3.  

Indicator of the new remote control flash 3 times after successful code learning.

Remote control RF code learning from drivers

1.  

Turn off the power supply of the controllers.

2.  

Press and hold 

“ON/OFF”

 key for 5 seconds until indicator of wall panel is flashing.

3.  

Turn on the power supply of the controllers. Indicator of the remote control flashes 3 times after successful code learning.

Note:

The distance from controllers to remote controls should be less than 2 meters.

STEP

OPERATION

INSTRUCTIONS

1

Disconnect the power to the receiver > Wait 5 seconds >  Reconnect the 

power to the receiver.

Remember that for the following steps to work you 

need to have done the “Code Clearing” step. If you have 

multiple drivers, only power the one you wish to pair.

2

On the wall panel, press and hold the “Night Light Key”         for 5 seconds.

The lights and the Wall panel wil now start to flash. 

This means pairing is succesful.

3

Press the POWER-button after the wall panel starts blinking to end pairing 

mode.

You will now leave pairing mode, which stops the 

blinking. This will also happen automatically after 60 

seconds.

Code Matching: This ensures only the desired remote control will be able to controle the driver. 

Attention: 

This step does not require the remote that comes with the driver. You will only need to have the desired remote control and have done the 

“Code clearing” step.

EN

Summary of Contents for ITL2.4GMD













Reviews: