background image

While opening the package, please check whether all 

the 

components are complete. If 

anything is missing,   please contact the dealer immediately. 

Specifications:

Wingspan

Fuselage length

Wing area

Takeoff weight
Center of gravity: 

108mm back from the leading edge next to the fuselage

Recommended power configuration: 

Motor: Shuangtian 3542/950kv  exodeviation brushless motor

 

Electronic tuning:  Haoying40A
Battery
Propeller

Servos

Flight precautions
Do not fly in following circumstances:

1.

In 

 bad weather conditions

 

such as strong wind

s

 

poor visibility

 

and rain.

2.

W

here there is

 strong electromagnetic interference

 

such as near high-tension lin

es

3.

Near high buildings, trees or street lamps.

4.

Without guidance of 

an 

experienced person i

f you have never flown before

.

5.

Attention: 

Model 

 airplane

s

 

are

 not toy

s

, you are fully responsible for 

the 

safety of 

the 

flight.

Storage precautions:

1.

The battery must be 

removed from the airplane 

 before stor

ing 

 in case of 

fire

.

2. When storing the model it is best to hang it on a rack from its propeller.

 

Attention: 

D

ue to continuous 

updating

 of product

there may be some tiny differences between the 

instruction book and 

the 

actual product.

Recommended control throws:

Ailerons: 3D flying 40 degrees/Normal flying 25 degrees.

Elevator: 3D flying 40 degrees/Normal flying 25 degrees.

Rudder: 3D flying 50 degrees/Normal flying 25 degrees.

Summary of Contents for Katana EPP-30E








Reviews: