manualshive.com logo in svg

Hobby-Lobby HLI8601 F-86 Sabre Skyblazers, Instruction Manual

Share
Download
Hobby-Lobby HLI8601 F-86 Sabre Skyblazers Instruction Manual Download Page 8

15. Place battery in fuselage and install Velcro through the slots in battery tray. Strap battery in 
place as shown. Battery and ESC have pre-installed genuine Deans Ultra plugs for excellent 
connectivity and reliable performance.  
             

           

 

 
16. Canopy has pre-installed magnets at the front. Insert tab at rear of canopy and snap front 
into position. A sheet of water slide star decals is supplied; follow the photo on the box for star 
placement. Soak decal in water for about 15 seconds and let stand for 60 seconds then slide 
off backing paper into position on airplane. Allow decals to dry before flight. 

 

            

             

 

17. Aileron control throws are 7/16” up and 5/16” down. If using the Y-connector you will not be 
able to adjust aileron differential. Set the up throw to be about 7/16” -1/2”. Elevator control 
throws are 7/16” in both directions.           
           

  

          

 

Summary of Contents for HLI8601 F-86 Sabre Skyblazers











Reviews:

No comments

Brands by name

Popular brands

Load more brands