background image

2

GENERAL INFORMATIONS

 

Read this manual and its safety precautions carefully! Keep this manual and if 
you give the model to a third party, put this manual to the model.

 

Take care, that you are familiar with your transmitter and all electronic 
components, used in your plane.

 

Take care of all safety instructions of tools, which are you using to assemble 
this model.

 

Only take glues, which are recommended for the specific materials and which 
are approved for model business.

 

Before assembling please check all parts of this kit. If some parts are missing or 
have a mistake, please call our service center.

ENVIRONMENT PROTECTION INFOS

 

The symbols on the package show 
you, that the model and its accessories 
should not be put to waste. All 
electric and electronic parts should 
be deposed to places of waste 
management.

 

Batteries and accumulators must be removed from the 
devices and should be deposed to the correct waste 
management organisation. Take information from your 
home town government.

ENGLISH

TABLE OF CONTENTS

General informations ......................................................................2

Environment protection infos ....................................................2

Introduction ........................................................................................2

Safety precautions ...........................................................................3

Recommended accessories ..........................................................4

Adhesives and Building Supplies ............................................4

Kit check ................................................................................................4

Spare parts for the Midi Edge 540 ............................................4

Choosing the motor set .................................................................5

Wings assembly .................................................................................5

Elevator assembly.............................................................................6

Rudder assembly ...............................................................................7

Landing gear assembly ..................................................................8

Engine .....................................................................................................9

RC components ............................................................................... 11

Get the model ready to fly ......................................................... 11

Check the Control Directions ................................................ 11

Balance the Model (C.G.) ......................................................... 12

Balance the Model Laterally .................................................. 12

Set the Control Throws ............................................................ 12

Preflight .............................................................................................. 13

Charge the Batteries ................................................................. 13

Balance Propellers ..................................................................... 13

Range check ................................................................................ 13

Check-List .......................................................................................... 14

Introduction

The Flitework Midi Edge 540 is designed for aerobatic flight and offers a plenty of fun. You can choose 2 different 

kinds of motor sets, one for 3D aerobatic flight and another for speed flight. The speed version of Midi Edge 540 

reaches about 180 km/h (110 mph).

Attention please!

Remote controlled model planes are not a toy! For assembling, flying and servicing such models, you need a high 

grade of technical comprehension and liability.

Careless assembling and operation may cause personal and material damage.

Because the Flitework GmbH has no influence on assembly, RC installation, operation and servicing of the flight 

device, any liability is rejected under explicit advice to these dangers.

Summary of Contents for Midi EDGE 540 FLWA4001

















Reviews: