background image

Warranty

AquaCraft

will warrant this kit* for 90 days after the purchase from defects in materials or workmanship. AquaCraft

will either repair or replace, at no charge, the incorrectly made part.

Make sure you save the receipt or invoice you were given when you bought your model! It is your proof of purchase
and we must see it before we can honor the warranty.

To return your V24 One-Design for repairs covered under warranty, you should send your boat to:

Hobby Services 

3002 N. Apollo Drive, Suite 1

Champaign, Illinois 61822

Attn: Service Department

Phone: (217) 398-0007 9:00 am - 5:00 pm Central Time M-F

E-mail:

[email protected]

*See engine warranty information on page 2

HCAZ

1003

 for HCAB

40

**

Entire Contents © Copyright 2005

ASSEMBLY AND OPERATION MANUAL

by

Thank you for purchasing the V24 One-Design! We at AquaCraft know how exciting a new R/C boat purchase can be and
we know you’re anxious to get started, but please take time to read these instructions carefully and completely before
attempting to operate your model. This manual contains the instructions you need to safely operate and maintain your
boat. As with any hobby, there is the possibility of injury. Arming yourself with knowledge is the best way to avoid injury.

If for any reason you think that this model is not for you, return it to your local dealer immediately. PLEASE NOTE:
Your hobby dealer cannot accept a return on any model after the final assembly sequence has begun.

Summary of Contents for AquaCraft V24 One-Design

















Reviews: