HK Instruments CDT 2000 Duct Series Installation Instructions Download Page 4

Copyright HK Instruments 2017

www.hkinstruments.fi

Installation version 5.0 2017

WARRANTY POLICY

The seller is obligated to provide a warranty of five years for the deliv

-

ered goods regarding material and manufacturing. The warranty period 
is considered to start on the delivery date of the product. If a defect in 
raw materials or a production flaw is found, the seller is obligated, when 
the product is sent to the seller without delay or before expiration of 
the warranty, to amend the mistake at his/her discretion either by re

-

pairing the defective product or by delivering free of charge to the buy

-

er a new flawless product and sending it to the buyer. Delivery costs 
for the repair under warranty will be paid by the buyer and the return 
costs by the seller. The warranty does not comprise damages caused by 
accident, lightning, flood or other natural phenomenon, normal wear 
and tear, improper or careless handling, abnormal use, overloading, im

-

proper storage, incorrect care or reconstruction, or changes and instal

-

lation work not done by the seller or his/her authorized representative. 
The selection of materials for devices prone to corrosion is the buyer’s 
responsibility, unless otherwise is legally agreed upon. Should the man

-

ufacturer alter the structure of the device, the seller is not obligated to 
make comparable changes to devices already purchased. Appealing for 
warranty requires that the buyer has correctly fulfilled his/her duties 
arisen from the delivery and stated in the contract. The seller will give 
a new warranty for goods that have been replaced or repaired within 
the warranty, however only to the expiration of the original product’s 
warranty time. The warranty includes the repair of a defective part or 
device, or if needed, a new part or device, but not installation or ex

-

change costs. Under no circumstance is the seller liable for damages 
compensation for indirect damage.

RECYCLING/DISPOSAL

The  parts  left  over  from  installation  should  be 
recycled  according  to  your  local  instructions. 
Decommissioned  devices  should  be  taken  to  a 
recycling site that specializes in electronic waste.

SELCOUSA.com 

Summary of Contents for CDT 2000 Duct Series

Page 1: ...o to be unoccupied for four hours per day so that the indoor CO2 concentration drops to the outside level CDT2000 DC Duct is a dual channel model with a measuring channel and a reference channel that makes a continuous comparison and the necessary adjustment accordingly CDT2000 DC Duct is also suitable for buildings that are continuously occupied CDT2000 Duct series devices are commonly used to mo...

Page 2: ...e device as a template and mark the screw holes 3 Mount the flange on the duct with screws not included Figure 1a 4 Adjust the probe to the desired depth Ensure that the end of the probe reaches the middle of the duct Figure 1b 5 Tighten the screw on the flange to hold the probe in position Figure 1a Mounting a flange Figure 1b Mounting the probe in a flange Air flow direction Air flow direction Air...

Page 3: ...DOWN 4 Select the temperature low limit for output band 0 45 0 C or 32 112 F TE OUT MIN 0 0 C SELECT UP DOWN 5 Select the temperature high limit for output band 5 50 0 C or 42 122 F 6 Select the output maximum voltage 5 V 10 V TE OUT MAX 50 0 C SELECT UP DOWN MAX OUTPUT V 10 V SELECT UP DOWN 7 Select the output minimum voltage 0 V 2 V MIN OUTPUT V 0 V SELECT UP DOWN 8 Push the select button to exi...

Page 4: ... incorrect care or reconstruction or changes and instal lation work not done by the seller or his her authorized representative The selection of materials for devices prone to corrosion is the buyer s responsibility unless otherwise is legally agreed upon Should the man ufacturer alter the structure of the device the seller is not obligated to make comparable changes to devices already purchased A...

Reviews: