15
7.4.5.5
Muting Outputs
The SPEAKER, SCENE, LEVEL, DELAY/PHASE and
ADMIN keys serve the second purpose of muting
outputs. The label above each key tells you its
mute function. To mute outputs, press and hold
the MUTE/HOLD key and press the key of the
output you wish to mute (key A to D for Output A to
Output D). The Lim/Mute LED in the given output’s
LED chain lights up red to indicate the output is
muted. Follow the same procedure to enable the
output.
7.5 Firmware
The FIRNET controller ships with the current fi rm-
ware. LIPAN software lets you update the device
with future fi rmware versions. See chapter 4 LIPAN
PC Software, to learn more about fi rmware updates.
This is to certify that
HK AUDIO
®
FIRNET
complies with the provisions of the Directive of
the Council of the European Communities on
the approximation of the laws of the Member
States relating to electromagnetic compatibility
according to EMC Directive 89/336/EEC inclu-
ding amendment 93/68/EEC and the low voltage
Directive 73/23/EEC including amendment 93/68/
EEC. This declaration of conformity of the Euro-
pean Communities is the result of an examination
carried out by the Quality Assurance Department
of STAMER GmbH in accordance with European
Standards EN 50081-1, EN 50082-1and EN 60065
for low voltage.
Magdeburger Str. 8
66606 St. Wendel • Germany
Lothar Stamer Dipl.Ing.
Managing Director
St. Wendel, 01/08/08
Version 1.0 09/2007
8 Technical Data
Connectors
Analog Input
3-pin XLR female
Pin assignments
1 = ground, 2 = signal (+), 3 = signal (-)
Input impedance
9 k-ohms
Maximum input level
Variable; 6, 12, 18, and 24 dBu
Dynamic range, input
> 128 dB (A)
Digital input
3-pin XLR female
Pin assignments
1 = ground, 2 = signal, 3 = signal
Input impedance
110 ohms
Protocol
AES 3 (AES/EBU)
Clock rate
Switchable to 48 or 96 kHz
Synchronization
To an external source (slave mode)
Digital output
3-pin XLR male
Pin assignments
1 = ground, 2 = signal, 3 = signal
Output impedance
110 ohms
Protocol
AES 3 (AES/EBU)
Signal processing
Refresh signal form and level
(Bypass at power failure)
Analog outputs
3-pin XLR male
Pin assignments
1 = ground, 2 = signal (+), 3 = signal (-)
Output impedance
35 ohms
Maximum output level
Variable; 6, 12, 18, and 24 dBu
Dynamic range, output
> 125 dB (A)
Mains voltage connector
Three-pole non-heating equipment
connector
Mains voltage / frequency
100 to 240 V / 50 - 60 Hz
Power consumption
40 VA
Max. curr. cons. at 100 V mains volt.
400 mA
Max. curr. cons. at 230 V mains volt.
175 mA
Ethernet X port
RJ-45, RJ-45, cross-connected
Ethernet II port
RJ-45, RJ-45, direct-connected
Audio data
(Linear Through mode)
Frequency response (-1 dB)
5.5 Hz to 34 KHz
THD+N (20 Hz to 20 kHz)
AD>DA input level 21dBu,
R=100k, 96 kHz 0.0012%-0.0013%
AES>DA input level -3dBFS,
R=100k, 96 kHz 0.0010% - 0.0012%
Latency (incl. limiter):
AD > DA 96 KHz 3.15ms
AD > AES/EBU 96 KHz
AES/EBU > A 96 KHz
+ fi lter (Cohedra / Coh. Compact)
5.8 ms
Digital signal processing
Internal sampling rate
96 kHz
Internal data format
32-bit fl oating point
AD converter resolution
28 bits
DA converter resolution
24 bits
Operating conditions
Temperature range
-10° C to +70°C
Hardware specifications
Weight
6.6 lbs. • 3 kg
Measurements (D x H x W)
48 x 4.4 x 23.2 cm
18-7/8 x 17-5/16 x 9-1/8"
English